- 著者
- Toshie HIDARI Toshiki TAKAMIZAWA Arisa IMAI Eizo HIROKANE Ryo ISHII Akimasa TSUJIMOTO Takayuki SUZUKI Masashi MIYAZAKI
- 出版者
- The Japanese Society for Dental Materials and Devices
- 雑誌
- Dental Materials Journal (ISSN:02874547)
- 巻号頁・発行日
- pp.2019-154, (Released:2020-02-29)
- 参考文献数
- 37
- 被引用文献数
- 16
This study aimed to determine the role of the 10-methacryloyloxydecyl dihydrogen phosphate (MDP) in dentin bond durability of universal adhesive in etch-&-rinse mode through bond strength tests after different degradation conditions. This study used the MDP-containing universal adhesive, Clearfil Universal Bond Quick (CU), and an experimental adhesive (NM) made with the same ingredients as CU, excluding MDP. Shear bond strength (SBS) to dentin were obtained in etch-&-rinse mode with or without MDP. CU in self-etch mode was used as a comparison. The groups were divided into three types: 1) subjected to thermal cycling; 2) subjected to long-term water storage; and 3) stored in water for 24 h, as a baseline. The discrepancies in the mean SBS of the CU and NM groups become prominent with prolonged degradation periods. This study indicates that the MDP in universal adhesive might play a key role in enhancing dentin bond quality even when etch-&-rinse mode is used.
- 著者
- Yukie TAMURA Toshiki TAKAMIZAWA Yutaka SHIMAMURA Shunsuke AKIBA Chiaki YABUKI Arisa IMAI Akimasa TSUJIMOTO Hiroyasu KUROKAWA Masashi MIYAZAKI
- 出版者
- 日本歯科理工学会
- 雑誌
- Dental Materials Journal (ISSN:02874547)
- 巻号頁・発行日
- pp.2016-185, (Released:2017-07-12)
- 参考文献数
- 30
- 被引用文献数
- 12
The influences of air-powder polishing with glycine or sodium bicarbonate powders on shear bond strengths (SBS) and surface-free energies of universal adhesives were examined. Scotchbond Universal Adhesive (SU, 3M ESPE), G-Premio Bond (GP, GC), Adhese Universal (AU, Ivoclar Vivadent), and All-Bond Universal (AB, Bisco) were used in this study. Bovine dentin surfaces were air polished with glycine or sodium bicarbonate powders prior to the bonding procedure, and resin pastes were bonded to the dentin surface using universal adhesives. SBSs were determined after 24-h storage in distilled water at 37°C. Surface-free energy was then determined by measuring contact angles using three test liquids on dentin surfaces. Significantly lower SBSs were observed for dentin that was air-powder polished and surface-free energies were concomitantly lowered. This study indicated that air-powder polishing influences SBSs and surface-free energies. However, glycine powder produced smaller changes in these surface parameters than sodium bicarbonate.
- 著者
- Chie KANAZAWA Ryosuke MURAYAMA Tetsuya FURUICHI Arisa IMAI Shunichi SUDA Hiroyasu KUROKAWA Toshiki TAKAMIZAWA Masashi MIYAZAKI
- 出版者
- 日本歯科理工学会
- 雑誌
- Dental Materials Journal (ISSN:02874547)
- 巻号頁・発行日
- pp.2016-175, (Released:2016-12-06)
- 参考文献数
- 28
This study used an ultrasonic measurement device to monitor the setting behavior of silicone elastomeric impression materials, and the influence of temperature on setting behavior was determined. The ultrasonic device consisted of a pulser-receiver, transducers, and an oscilloscope. The two-way transit time through the mixing material was divided by two to account for the down-and-back travel path; then it was multiplied by the sonic velocity. Analysis of variance and the Tukey honest significant difference test were used. In the early stages of the setting process, most of the ultrasonic energy was absorbed by the elastomers and the second echoes were relatively weak. As the elastomers hardened, the sonic velocities increased until they plateaued. The changes in sonic velocities varied among the elastomers tested, and were affected by temperature conditions. The ultrasonic method used in this study has considerable potential for determining the setting processes of elastomeric impression materials.