著者

鞍谷 文保 北林 研人 小川 渉 吉田 達哉 長村 光造 小出 俊雄 文珠 義之 水田 泰次

出版者

一般社団法人 日本機械学会

雑誌

日本機械学会論文集 (ISSN:21879761)

巻号頁・発行日

vol.83, no.851, pp.17-00110, 2017 (Released:2017-07-25)

参考文献数

13

---

Cymbals are percussion instruments that vibrate and radiate sounds when hit with a stick or when used in pairs. The sound radiated from a cymbal depends on its vibration characteristics. Cymbals are made through spin forming, hammering and lathing processes. The spin forming creates the domed shape of cymbals, determining the basic vibration characteristics. The hammering and lathing make specific sound quality adjustments by changing the vibration characteristics. In this paper, we focus on how the hammering affects the cymbal's vibration characteristics. The hammering produces many shallow dents over the cymbal's surface, generating residual stresses in it. These residual stresses change the vibration characteristics. We perform finite element analysis of the hammered cymbal to obtain its vibration characteristics. In the analysis, we use thermal stress analysis to reproduce the stress distribution and then with this stress distribution we perform vibration analysis. The results show that the effects of thermal load (i.e., hammering) vary depending on the mode: an increase or decrease in the natural frequency. As a result, the peak frequencies and their peak values in the frequency response function change.

著者

北林 研人 石原 匡 鞍谷 文保 吉田 達哉 小出 俊雄 水田 泰次 長村 光造

出版者

一般社団法人 日本機械学会

雑誌

Dynamics & Design Conference 2016 (ISSN:24242993)

巻号頁・発行日

pp.340, 2016 (Released:2017-06-19)

---

Cymbals are thin domed plates used as percussion instruments. When cymbals are stuck, they vibrate and radiate sound. Cymbals are made through spin forming, hammering, and lathing. The sound radiated from a cymbal depends on its vibration characteristics that are determined by the shape and dimension. The hammering produces plastic deformation on the cymbal's surface, generating residual stresses throughout it. Although the vibration characteristics are changed by the hammering to adjust cymbal sound, the effect of the hammering on the cymbal sound is not clear. In this paper, we reveal the effect of the hammering on the vibration and the sound radiation characteristics. The stress distribution within the cymbal produced by hammering is reproduced by thermal stress analysis and the change in natural frequency of the modes are calculated by the vibration analysis with the stress distribution. The change (i.e., increase or decrease) in natural frequency for each mode is explained by the stress and modal strain energy distributions.

著者

鞍谷 文保 北林 研人 小川 渉 吉田 達哉 長村 光造 小出 俊雄 文珠 義之 水田 泰次

出版者

一般社団法人 日本機械学会

雑誌

日本機械学会論文集 (ISSN:21879761)

巻号頁・発行日

pp.17-00110, (Released:2017-07-06)

参考文献数

13

---

Cymbals are percussion instruments that vibrate and radiate sounds when hit with a stick or when used in pairs. The sound radiated from a cymbal depends on its vibration characteristics. Cymbals are made through spin forming, hammering and lathing processes. The spin forming creates the domed shape of cymbals, determining the basic vibration characteristics. The hammering and lathing make specific sound quality adjustments by changing the vibration characteristics. In this paper, we focus on how the hammering affects the cymbal's vibration characteristics. The hammering produces many shallow dents over the cymbal's surface, generating residual stresses in it. These residual stresses change the vibration characteristics. We perform finite element analysis of the hammered cymbal to obtain its vibration characteristics. In the analysis, we use thermal stress analysis to reproduce the stress distribution and then with this stress distribution we perform vibration analysis. The results show that the effects of thermal load (i.e., hammering) vary depending on the mode: an increase or decrease in the natural frequency. As a result, the peak frequencies and their peak values in the frequency response function change.