著者

Ryoki TAKANO Junichi HONDA Tatsuro KOBAYASHI Kei KUBOCHI Hiroki TAKATA Futoshi KOMINE

出版者

The Japanese Society for Dental Materials and Devices

雑誌

Dental Materials Journal (ISSN:02874547)

巻号頁・発行日

pp.2022-165, (Released:2022-12-07)

参考文献数

26

被引用文献数

2

---

The present study investigated the fracture strength of hybrid abutment crowns (HACs) in the premolar region that were fabricated with different restorative computer-aided design/computer-aided manufacturing (CAD/CAM) materials. The abutment-implant structures were randomly assigned into four groups (n=11 per group): bi-layered zirconia restorations (BL), translucent zirconia (4Y-PSZ) restorations (TZ), lithium disilicate ceramic restorations (LD), and dispersed nanoparticle-filled composite resin restorations (CM). All restorations were adhesively bonded to the titanium abutments. After the restoration-abutment complex was tightened onto the implant, the fracture strength was measured. The TZ (2.06 kN) and LD (1.87 kN) groups had significantly higher median fracture strengths than the BL (1.12 kN) and CM (1.10 kN) groups. In terms of fracture resistance, the 4Y-PSZ and lithium disilicate ceramic monolithic restorations would be superior to bi-layered 3Y-TZP and composite resin monolithic restorations for HACs in the premolar region.

著者

Futoshi Komine Junichi Honda Kosuke Kusaba Kei Kubochi Hiroki Takata Masanori Fujisawa

出版者

Nihon University School of Dentistry

雑誌

Journal of Oral Science (ISSN:13434934)

巻号頁・発行日

pp.20-0195, (Released:2020-08-01)

参考文献数

20

被引用文献数

5

---

Computer-aided design/computer-aided manufacturing (CAD/CAM) restorative materials have been widely used owing to a number of advantages, including stable quality of the materials, lower costs, and time-saving factors. Resin-based CAD/CAM materials for definitive restorations are classified into two groups: dispersed nanoparticle-filled composite resin and polymer-infiltrated-ceramic-network materials. Resin-based CAD/CAM materials have been applied to single crown restorations as a monolithic structure for the posterior region. In addition, resin-based CAD/CAM restorations have been applied recently for the anterior area. This literature review summarizes clinical outcomes, such as survival rates and clinical complications of single crown restorations fabricated with resin-based CAD/CAM materials.

著者

Yuta MORIYA Futoshi KOMINE Junichi HONDA Kosuke KUSABA Jin KITANI Hideo MATSUMURA

出版者

The Japanese Society for Dental Materials and Devices

雑誌

Dental Materials Journal (ISSN:02874547)

巻号頁・発行日

pp.2019-216, (Released:2020-05-22)

参考文献数

29

---

To investigate the effect of luting agent type on fracture loads of implant-supported ceramic prostheses in premolar region. Ninety-nine implant-abutment complexes were divided into three different implant-supported prostheses: monolithic yttria-partially stabilized zirconia (Y-PSZ) restorations (MPZ specimens), porcelain layered on yttria-stabilized tetragonal zirconia polycrystal (Y-TZP) restorations (PLZ specimens), and monolithic lithium disilicate ceramic restorations (MLD specimens). Implant-supported prostheses were luted with adhesive resin luting agent (RLA), glass ionomer cement (GIC), or zinc phosphate cement (ZPC). For MPZ and MLD specimens, fracture loads were significantly higher for RLA group than for GIC and ZPC groups. For PLZ specimens, fracture loads did not significantly differ in relation to luting agent. Fracture loads were significantly higher for MPZ specimens than for other test specimens, regardless of luting agent. Use of an adhesive resin luting agent is recommended for placement of premolar implant-supported monolithic Y-PSZ and lithium disilicate ceramic prostheses.

著者

Yoshiro Hadano Junichi Honda

出版者

一般社団法人 日本内科学会

雑誌

Internal Medicine (ISSN:09182918)

巻号頁・発行日

vol.56, no.15, pp.2085-2085, 2017-08-01 (Released:2017-08-01)

参考文献数

2

被引用文献数

2