著者

Ryoki TAKANO Junichi HONDA Tatsuro KOBAYASHI Kei KUBOCHI Hiroki TAKATA Futoshi KOMINE

出版者

The Japanese Society for Dental Materials and Devices

雑誌

Dental Materials Journal (ISSN:02874547)

巻号頁・発行日

pp.2022-165, (Released:2022-12-07)

参考文献数

26

被引用文献数

2

---

The present study investigated the fracture strength of hybrid abutment crowns (HACs) in the premolar region that were fabricated with different restorative computer-aided design/computer-aided manufacturing (CAD/CAM) materials. The abutment-implant structures were randomly assigned into four groups (n=11 per group): bi-layered zirconia restorations (BL), translucent zirconia (4Y-PSZ) restorations (TZ), lithium disilicate ceramic restorations (LD), and dispersed nanoparticle-filled composite resin restorations (CM). All restorations were adhesively bonded to the titanium abutments. After the restoration-abutment complex was tightened onto the implant, the fracture strength was measured. The TZ (2.06 kN) and LD (1.87 kN) groups had significantly higher median fracture strengths than the BL (1.12 kN) and CM (1.10 kN) groups. In terms of fracture resistance, the 4Y-PSZ and lithium disilicate ceramic monolithic restorations would be superior to bi-layered 3Y-TZP and composite resin monolithic restorations for HACs in the premolar region.

著者

Keisuke MATSUSHIMA Kei KUBOCHI Futoshi KOMINE Fumiaki KIMURA Tatsuro KOBAYASHI Hideo MATSUMURA

出版者

The Japanese Society for Dental Materials and Devices

雑誌

Dental Materials Journal (ISSN:02874547)

巻号頁・発行日

pp.2021-141, (Released:2021-09-04)

参考文献数

27

被引用文献数

1

---

The effects of mechanical retentive devices and various surface treatments on the shear bond strength between a veneering composite resin and zirconia was investigated. Zirconia disks were classified into three surface-treatment groups: airborne-particle abrasion, overglazing, and overglazing with white alumina particles of three different grain sizes (50, 70, and 105 μm) attached onto zirconia disks (ZR-50, ZR-70, and ZR-105, respectively). They were further divided into four groups (n=44): unprimed, Clearfil Porcelain Bond Activator (CA), Clearfil Photo Bond (CB), and CA+CB. An indirect composite resin was bonded to zirconia specimens. Shear bond strengths were measured. For the ZR-70 and ZR-105 groups, the CB and CA+CB specimens exhibited higher bond strengths than the other two specimens after thermocycling. The ZR-70 and ZR-105 groups achieved micromechanical interlocking, and priming with a phosphate monomer (MDP) yielded stable bond strengths between the composite resin and zirconia with alumina particles attached as retentive devices.

著者

Futoshi KOMINE Fumiaki KIMURA Kei KUBOCHI Ryoki TAKANO Daishi NAKASE Hideo MATSUMURA

出版者

The Japanese Society for Dental Materials and Devices

雑誌

Dental Materials Journal (ISSN:02874547)

巻号頁・発行日

pp.2020-175, (Released:2021-01-15)

参考文献数

32

被引用文献数

1

---

This study investigated the influence of roughening procedures and application of primers on shear bond strengths of CAD/CAM composite resin material or ceramic material to zirconia frameworks. A CAD/CAM composite resin block (Katana Avencia Block; AVE) and lithium disilicate glass-ceramic block (IPS e.max CAD; IEC) were used as veneer materials. The veneers were divided into three surface treatment groups; HF, hydrofluoric acid etching; AB, airborne-particle abrasion; and CON, no surface treatment. Each veneer was primed with four agents: Clearfil Porcelain Bond Activator (ACT), Clearfil Photo Bond (CPB), Clearfil Photo Bond with Porcelain Bond Activator (CPB+ACT), and no priming (UP). The zirconia frameworks and AVE or IEC veneers were resin-bonded. In the AVE specimen, AB treatment showed significantly higher shear bond strength than the other treatments at 0 and 20,000 thermocycles, except for UP and CPB+ACT groups at 20,000 thermocycles. Airborne-particle abrasion is necessary for resin bonding to Avencia blocks.

著者

Futoshi Komine Junichi Honda Kosuke Kusaba Kei Kubochi Hiroki Takata Masanori Fujisawa

出版者

Nihon University School of Dentistry

雑誌

Journal of Oral Science (ISSN:13434934)

巻号頁・発行日

pp.20-0195, (Released:2020-08-01)

参考文献数

20

被引用文献数

5

---

Computer-aided design/computer-aided manufacturing (CAD/CAM) restorative materials have been widely used owing to a number of advantages, including stable quality of the materials, lower costs, and time-saving factors. Resin-based CAD/CAM materials for definitive restorations are classified into two groups: dispersed nanoparticle-filled composite resin and polymer-infiltrated-ceramic-network materials. Resin-based CAD/CAM materials have been applied to single crown restorations as a monolithic structure for the posterior region. In addition, resin-based CAD/CAM restorations have been applied recently for the anterior area. This literature review summarizes clinical outcomes, such as survival rates and clinical complications of single crown restorations fabricated with resin-based CAD/CAM materials.

著者

Fumiaki Kimura Futoshi Komine Kei Kubochi Shogo Yagawa

出版者

Nihon University School of Dentistry

雑誌

Journal of Oral Science (ISSN:13434934)

巻号頁・発行日

vol.61, no.2, pp.327-334, 2019 (Released:2019-06-18)

参考文献数

25

被引用文献数

2

---

This study investigated bond strength of CAD/CAM-manufactured composite resin and ceramic veneers to a zirconia framework and analyzed the effect of treatments of veneer surfaces. A CAD/CAM resin-based (AVE) composite or lithium disilicate ceramic (IEC) block was used as the veneer material. AVE and IEC specimens were assigned to receive one of three surface treatments (n = 22): no surface treatment, acid-etching with 9.5% hydrofluoric acid gel, and airborne-particle abrasion with alumina particles. Zirconia disks and AVE or IEC specimens in each group were bonded with a resin-based luting agent, and shear bond strength of the specimens was measured at 0 and 20,000 thermocycles. Significant differences were assessed by the Steel-Dwass test for multiple comparisons and Mann-Whitney U-test (α = 0.05). As compared with other surface treatments, bond strengths were significantly higher at 0 and 20,000 thermocycles in the airborne-particle abraded AVE and acid-etched IEC specimens. Airborne-particle abrasion of the surface of AVE specimens increased bond strength between AVE veneers and zirconia frameworks, while hydrofluoric acid treatment enhanced bond strength between IEC veneers and zirconia frameworks.

著者

Serina Taguchi Futoshi Komine Kei Kubochi Ryosuke Fushiki Fumiaki Kimura Hideo Matsumura

出版者

Nihon University School of Dentistry

雑誌

Journal of Oral Science (ISSN:13434934)

巻号頁・発行日

pp.17-0383, (Released:2018-08-25)

参考文献数

35

被引用文献数

8

---

This study examined the effect of silane and phosphate functional monomer on bond strengths between a resin-based luting agent joined to a lithium disilicate ceramic (IPS e.max) and silica (quartz) materials. The e.max and quartz specimens were assigned to 6 groups with different priming/bonding agents, namely, Clearfil Porcelain Bond Activator, Clearfil Photo Bond, Clearfil Photo Bond Universal with Clearfil Porcelain Bond Activator, Clearfil Photo Bond Catalyst with Clearfil Porcelain Bond Activator, Clearfil Photo Bond with Clearfil Porcelain Bond Activator, and unprimed. The corresponding specimens were bonded by using a resin-based luting agent (Panavia V5). Shear bond strengths were determined before and after 5,000 thermocycles. For both the e.max and quartz specimens, the Clearfil Photo Bond Universal with Clearfil Porcelain Bond Activator group had the highest pre- and post-thermocycling bond strength values. Combined use of silane in the acidic environment of a phosphate functional monomer and initiators enhances bond strength of a resin-based luting agent to e.max ceramic and quartz materials.

著者

Taro IWASAKI Futoshi KOMINE Ryosuke FUSHIKI Kei KUBOCHI Mitsuyo SHINOHARA Hideo MATSUMURA

出版者

日本歯科理工学会

雑誌

Dental Materials Journal (ISSN:02874547)

巻号頁・発行日

vol.35, no.3, pp.461-469, 2016-05-31 (Released:2016-06-01)

参考文献数

36

被引用文献数

15

---

This study evaluated shear bond strengths of a layering indirect composite material to a zirconia framework material treated with tribochemical silica coating. Zirconia disks were divided into two groups: ZR-PRE (airborne-particle abrasion) and ZR-PLU (tribochemical silica coating). Indirect composite was bonded to zirconia treated with one of the following primers: Clearfil Ceramic Primer (CCP), Clearfil Mega Bond Primer with Clearfil Porcelain Bond Activator (MGP+Act), ESPE-Sil (SIL), Estenia Opaque Primer, MR. Bond, Super-Bond PZ Primer Liquid A with Liquid B (PZA+PZB), and Super-Bond PZ Primer Liquid B (PZB), or no treatment. Shear bond testing was performed at 0 and 20,000 thermocycles. Post-thermocycling shear bond strengths of ZR-PLU were higher than those of ZR-PRE in CCP, MGP+Act, SIL, PZA+PZB, and PZB groups. Application of silane yielded better durable bond strengths of a layering indirect composite material to a tribochemically silica-coated zirconia framework material.