著者

Kei INAGAKI Kengo ISHIHARA Mariko ISHIDA Ai WATANABE Mika FUJIWARA Yuko KOMATSU Mika SHIRAI Yoshiho KATO Ami TAKANEZAWA Takashi FURUYASHIKI Hiroki TAKATA Yousuke SEYAMA

出版者

Center for Academic Publications Japan

雑誌

Journal of Nutritional Science and Vitaminology (ISSN:03014800)

巻号頁・発行日

vol.57, no.2, pp.170-176, 2011 (Released:2011-06-21)

参考文献数

23

被引用文献数

6 8

---

Enzymatically synthesized glycogen (ESG) has high solubility and its solution has low osmotic pressure. Therefore ESG solution could be rapidly absorbed and could be adequate for water rehydration and carbohydrate supplementation during exercise. The object of this study was to evaluate the gastric emptying time and plasma glucose elevation after an administration of ESG solution in comparison with another carbohydrate solution by using a laboratory animal. Male BALB/c mice were administered 10% w/v solution of glucose, maltodextrin, starch, naturally synthesized glycogen (NSG) and ESG at a dose of 20 μL/g body weight for the measurement of gastric emptying rate (Experiment 1) and 10 μL/g body weight for the measurement of plasma glucose elevation (Experiment 2). The osmolarity of gastric content was lower in the ESG and maltodextrin group than the other carbohydrate group. Weight of gastric fluid was significantly lower in the ESG and water group than the glucose group (p<0.01). Plasma glucose level was significantly lower in the ESG group than the glucose group from 0 to 60 min after administration (p<0.01), whereas plasma glucose level was same from 60 to 120 min for the ESG and glucose group (p=0.948). In Experiment 3, BALB/c mice ran on a treadmill for 2 h and were administered 8% of ESG or glucose solution (1.75, 3.5 or 7.0 μL/g body weight) every 20 min during running. There was no difference in post-exercise muscle glycogen level. These data suggest that 1) ESG beverage does not disturb water absorption because of its short gastric emptying time and 2) ESG slowly elevates plasma glucose level and maintains it for a prolonged time compared to the glucose solution.

著者

Ryoki TAKANO Junichi HONDA Tatsuro KOBAYASHI Kei KUBOCHI Hiroki TAKATA Futoshi KOMINE

出版者

The Japanese Society for Dental Materials and Devices

雑誌

Dental Materials Journal (ISSN:02874547)

巻号頁・発行日

pp.2022-165, (Released:2022-12-07)

参考文献数

26

被引用文献数

2

---

The present study investigated the fracture strength of hybrid abutment crowns (HACs) in the premolar region that were fabricated with different restorative computer-aided design/computer-aided manufacturing (CAD/CAM) materials. The abutment-implant structures were randomly assigned into four groups (n=11 per group): bi-layered zirconia restorations (BL), translucent zirconia (4Y-PSZ) restorations (TZ), lithium disilicate ceramic restorations (LD), and dispersed nanoparticle-filled composite resin restorations (CM). All restorations were adhesively bonded to the titanium abutments. After the restoration-abutment complex was tightened onto the implant, the fracture strength was measured. The TZ (2.06 kN) and LD (1.87 kN) groups had significantly higher median fracture strengths than the BL (1.12 kN) and CM (1.10 kN) groups. In terms of fracture resistance, the 4Y-PSZ and lithium disilicate ceramic monolithic restorations would be superior to bi-layered 3Y-TZP and composite resin monolithic restorations for HACs in the premolar region.

著者

Futoshi Komine Junichi Honda Kosuke Kusaba Kei Kubochi Hiroki Takata Masanori Fujisawa

出版者

Nihon University School of Dentistry

雑誌

Journal of Oral Science (ISSN:13434934)

巻号頁・発行日

pp.20-0195, (Released:2020-08-01)

参考文献数

20

被引用文献数

5

---

Computer-aided design/computer-aided manufacturing (CAD/CAM) restorative materials have been widely used owing to a number of advantages, including stable quality of the materials, lower costs, and time-saving factors. Resin-based CAD/CAM materials for definitive restorations are classified into two groups: dispersed nanoparticle-filled composite resin and polymer-infiltrated-ceramic-network materials. Resin-based CAD/CAM materials have been applied to single crown restorations as a monolithic structure for the posterior region. In addition, resin-based CAD/CAM restorations have been applied recently for the anterior area. This literature review summarizes clinical outcomes, such as survival rates and clinical complications of single crown restorations fabricated with resin-based CAD/CAM materials.

著者

Futoshi KOMINE Shingo KAMIO Hiroki TAKATA Shogo YAGAWA Serina TAGUCHI Kohei TAGUCHI Akiko HASHIGUCHI Hideo MATSUMURA

出版者

日本歯科理工学会

雑誌

Dental Materials Journal (ISSN:02874547)

巻号頁・発行日

pp.2017-057, (Released:2017-09-07)

参考文献数

41

被引用文献数

3

---

This study evaluated the effect of zirconia framework design on fracture load of implant-supported zirconia-based prostheses after thermal cycling and mechanical loading. Three different zirconia framework designs were investigated: uniform-thickness (UNI), anatomic (ANA), and supported anatomic (SUP) designs. Each framework was layered with feldspathic porcelain (ZAC group) or indirect composite material (ZIC group). The specimens then underwent fracture load testing after thermal cycling and cyclic loading. In the ZAC group, mean fracture load was significantly lower for UNI design specimens than for the other framework designs. In the ZIC group, there was no significant difference in mean fracture load between ANA design specimens and either UNI or SUP design specimens. To improve fracture resistance of implant-supported zirconia-based prostheses after artificial aging, uniformly thick layering material and appropriate lingual support with zirconia frameworks should be provided.