著者

Ping DU Akihiro NAKAO Satoshi MIKI Makoto INOUE

出版者

The Institute of Electronics, Information and Communication Engineers

雑誌

IEICE Transactions on Communications (ISSN:09168516)

巻号頁・発行日

vol.E103.B, no.4, pp.422-430, 2020-04-01 (Released:2020-04-01)

参考文献数

20

被引用文献数

3

---

In the coming smart-home era, more and more household electrical appliances are generating more and more sensor data and transmitting them over the home networks, which are often connected to Internet through Point-to-Point Protocol over Ethernet (PPPoE) for desirable authentication and accounting. However, according to our knowledge, high-speed commercial home PPPoE router is still absent for a home network environment. In this paper, we first introduce and evaluate our programmable platform FLARE-DPDK for ease of programming network functions. Then we introduce our effort to build a compact 10Gbps software FLARE PPPoE router on a commercial mini-PC. In our implementation, the control plane is implemented with Linux PPPoE software for authentication-like signaling control. The data plane is implemented over FLARE-DPDK platform, where we get packets from physical network interfaces directly bypassing Linux kernel and distribute packets to multiple CPU cores for data processing in parallel. We verify our software PPPoE router in both lab and production network environment. The experimental results show that our FLARE software PPPoE router can achieve much higher throughput than a commercial PPPoE router tested in a production environment.

著者

Sho TSUGAWA

出版者

The Institute of Electronics, Information and Communication Engineers

雑誌

IEICE Transactions on Communications (ISSN:09168516)

巻号頁・発行日

pp.2017EBI0003, (Released:2018-02-21)

被引用文献数

16

---

Socially aware networking is an emerging research field that aims to improve the current networking technologies and realize novel network services by applying social network analysis (SNA) techniques. Conducting socially aware networking studies requires knowledge of both SNA and communication networking, but it is not easy for communication networking researchers who are unfamiliar with SNA to obtain comprehensive knowledge of SNA due to its interdisciplinary nature. This paper therefore aims to fill the knowledge gap for networking researchers who are interested in socially aware networking but are not familiar with SNA. This paper surveys three types of important SNA techniques for socially aware networking: identification of influential nodes, link prediction, and community detection. Then, this paper introduces how SNA techniques are used in socially aware networking and discusses research trends in socially aware networking.

著者

Takashi SHIBATA Kazunori SATO Ryohei IKEJIRI

出版者

The Institute of Electronics, Information and Communication Engineers

雑誌

IEICE TRANSACTIONS on Electronics (ISSN:09168516)

巻号頁・発行日

vol.E100-C, no.11, pp.1012-1020, 2017-11-01

---

We conducted experimental classes in an elementary school to examine how the advantages of using stereoscopic 3D images could be applied in education. More specifically, we selected a unit of the Tumulus period in Japan for sixth-graders as the source of our 3D educational materials. This unit represents part of the coursework for the topic of Japanese history. The educational materials used in our study included stereoscopic 3D images for examining the stone chambers and Haniwa (i.e., terracotta clay figures) of the Tumulus period. The results of our experimental class showed that 3D educational materials helped students focus on specific parts in images such as attached objects of the Haniwa and also understand 3D spaces and concavo-convex shapes. The experimental class revealed that 3D educational materials also helped students come up with novel questions regarding attached objects of the Haniwa, and Haniwa's spatial balance and spatial alignment. The results suggest that the educational use of stereoscopic 3D images is worthwhile in that they lead to question and hypothesis generation and an inquiry-based learning approach to history.

著者

Sho TSUGAWA

出版者

The Institute of Electronics, Information and Communication Engineers

雑誌

IEICE TRANSACTIONS on Communications (ISSN:09168516)

巻号頁・発行日

vol.E102-B, no.1, pp.17-39, 2019-01-01

被引用文献数

16

---

Socially aware networking is an emerging research field that aims to improve the current networking technologies and realize novel network services by applying social network analysis (SNA) techniques. Conducting socially aware networking studies requires knowledge of both SNA and communication networking, but it is not easy for communication networking researchers who are unfamiliar with SNA to obtain comprehensive knowledge of SNA due to its interdisciplinary nature. This paper therefore aims to fill the knowledge gap for networking researchers who are interested in socially aware networking but are not familiar with SNA. This paper surveys three types of important SNA techniques for socially aware networking: identification of influential nodes, link prediction, and community detection. Then, this paper introduces how SNA techniques are used in socially aware networking and discusses research trends in socially aware networking.

著者

Javier Jose DIAZ RIVERA Waleed AKBAR Talha AHMED KHAN Afaq MUHAMMAD Wang-Cheol SONG

出版者

The Institute of Electronics, Information and Communication Engineers

雑誌

IEICE TRANSACTIONS on Communications (ISSN:09168516)

巻号頁・発行日

vol.E106-B, no.12, pp.1293-1301, 2023-12-01

被引用文献数

1

---

Zero Trust Networking (ZTN) is a security model where no default trust is given to entities in a network infrastructure. The first bastion of security for achieving ZTN is strong identity verification. Several standard methods for assuring a robust identity exist (E.g., OAuth2.0, OpenID Connect). These standards employ JSON Web Tokens (JWT) during the authentication process. However, the use of JWT for One Time Token (OTT) enrollment has a latent security issue. A third party can intercept a JWT, and the payload information can be exposed, revealing the details of the enrollment server. Furthermore, an intercepted JWT could be used for enrollment by an impersonator as long as the JWT remains active. Our proposed mechanism aims to secure the ownership of the OTT by including the JWT as encrypted metadata into a Non-Fungible Token (NFT). The mechanism uses the blockchain Public Key of the intended owner for encrypting the JWT. The blockchain assures the JWT ownership by mapping it to the intended owner's blockchain public address. Our proposed mechanism is applied to an emerging Zero Trust framework (OpenZiti) alongside a permissioned Ethereum blockchain using Hyperledger Besu. The Zero Trust Framework provides enrollment functionality. At the same time, our proposed mechanism based on blockchain and NFT assures the secure distribution of OTTs that is used for the enrollment of identities.

著者

Ryoya HONDA Minoru MIZUTANI Masaya TAMURA Takashi OHIRA

出版者

The Institute of Electronics, Information and Communication Engineers

雑誌

IEICE TRANSACTIONS on Electronics (ISSN:09168516)

巻号頁・発行日

vol.E106-C, no.11, pp.698-706, 2023-11-01

---

This paper formulates a class-E synchronous RF rectifier from a new viewpoint. The key point is to introduce a matrix and convolute the DC terms into RF matrices. The explicit expression of input impedance is demonstrated in plane geometry. We find out their input impedance exhibits a geodesic arc in hyperbolic geometry under ZVS operation, where the theoretical RF-DC conversion efficiency results in 100%. We verify the developed theory both numerically (circuit simulation) and experimentally (6.78MHz, 100W). We confirm that the input impedance becomes a geodesic arc for a wide range of DC load resistance. The presented theory is quite elegant since it is based on a matrix-based formulation and plane-geometrical expression.

著者

Guosheng ZHAO Yang WANG Jian WANG

出版者

The Institute of Electronics, Information and Communication Engineers

雑誌

IEICE TRANSACTIONS on Communications (ISSN:09168516)

巻号頁・発行日

vol.E106-B, no.8, pp.622-634, 2023-08-01

---

Internet of Things (IoT) devices are widely used in various fields. However, their limited computing resources make them extremely vulnerable and difficult to be effectively protected. Traditional intrusion detection systems (IDS) focus on high accuracy and low false alarm rate (FAR), making them often have too high spatiotemporal complexity to be deployed in IoT devices. In response to the above problems, this paper proposes an intrusion detection model of IoT based on the light gradient boosting machine (LightGBM). Firstly, the one-dimensional convolutional neural network (CNN) is used to extract features from network traffic to reduce the feature dimensions. Then, the LightGBM is used for classification to detect the type of network traffic belongs. The LightGBM is more lightweight on the basis of inheriting the advantages of the gradient boosting tree. The LightGBM has a faster decision tree construction process. Experiments on the TON-IoT and BoT-IoT datasets show that the proposed model has stronger performance and more lightweight than the comparison models. The proposed model can shorten the prediction time by 90.66% and is better than the comparison models in accuracy and other performance metrics. The proposed model has strong detection capability for denial of service (DoS) and distributed denial of service (DDoS) attacks. Experimental results on the testbed built with IoT devices such as Raspberry Pi show that the proposed model can perform effective and real-time intrusion detection on IoT devices.

著者

Xiaoyu WAN Yu WANG Zhengqiang WANG Zifu FAN Bin DUO

出版者

The Institute of Electronics, Information and Communication Engineers

雑誌

IEICE TRANSACTIONS on Communications (ISSN:09168516)

巻号頁・発行日

vol.E106-B, no.7, pp.571-577, 2023-07-01

---

In this paper, we investigate the sum rate (SR) maximization problem for downlink cooperative non-orthogonal multiple access (C-NOMA) system under in-phase and quadrature-phase (IQ) imbalance at the base station (BS) and destination. The BS communicates with users by a half-duplex amplified-and-forward (HD-AF) relay under imperfect IQ imbalance. The sum rate maximization problem is formulated as a non-convex optimization with the quality of service (QoS) constraint for each user. We first use the variable substitution method to transform the non-convex SR maximization problem into an equivalent problem. Then, a joint power and rate allocation algorithm is proposed based on successive convex approximation (SCA) to maximize the SR of the systems. Simulation results verify that the algorithm can improve the SR of the C-NOMA compared with the cooperative orthogonal multiple access (C-OMA) scheme.

著者

Sheng ZHANG Pengfei DU Helin YANG Ran ZHANG Chen CHEN Arokiaswami ALPHONES

出版者

The Institute of Electronics, Information and Communication Engineers

雑誌

IEICE TRANSACTIONS on Communications (ISSN:09168516)

巻号頁・発行日

vol.E106-B, no.2, pp.84-100, 2023-02-01

被引用文献数

1

---

In this paper, we report the recent progress in visible light positioning and communication systems using light-emitting diodes (LEDs). Due to the wide deployment of LEDs for indoor illumination, visible light positioning (VLP) and visible light communication (VLC) using existing LEDs fixtures have attracted great attention in recent years. Here, we review our recent works on visible light positioning and communication, including image sensor-based VLP, photodetector-based VLP, integrated VLC and VLP (VLCP) systems, and heterogeneous radio frequency (RF) and VLC (RF/VLC) systems.

著者

Haiyan SUN Xingyu WANG Zheng ZHU Jicong ZHAO

出版者

The Institute of Electronics, Information and Communication Engineers

雑誌

IEICE TRANSACTIONS on Electronics (ISSN:09168516)

巻号頁・発行日

vol.E106-C, no.3, pp.76-83, 2023-03-01

被引用文献数

1

---

In this paper, the spurious modes and quality-factor (Q) values of the one-port dual-mode AlN lamb-wave resonators at 500-1000 MHz were studied by theoretical analysis and experimental verification. Through finite element analysis, we found that optimizing the width of the lateral reflection boundary at both ends of the resonator to reach the quarter wavelength (λ/4), which can improve its spectral purity and shift its resonant frequency. The designed resonators were micro-fabricated by using lithography processes on a 6-inch wafer. The measured results show that the spurious mode can be converted and dissipated, splitting into several longitudinal modes by optimizing the width of the lateral reflection boundary, which are consistent well with the theoretical analysis. Similarly, optimizing the interdigital transducer (IDT) width and number of IDT fingers can also suppress the resonator's spurious modes. In addition, it is found that there is no significant difference in the Qs value for the two modes of the dual-mode resonator with the narrow anchor and full anchor. The acoustic wave leaked from the anchor into the substrate produces a small displacement, and the energy is limited in the resonator. Compared to the resonator with Au IDTs, the resonator with Al IDTs can achieve a higher Q value due to its lower thermo-elastic damping loss. The measured results show the optimized dual-mode lamb-wave resonator can obtain Qs value of 2946.3 and 2881.4 at 730.6 MHz and 859.5 MHz, Qp values of 632.5 and 1407.6, effective electromechanical coupling coefficient (k2eff) of 0.73% and 0.11% respectively, and has excellent spectral purity simultaneously.

著者

Akito IGUCHI Yasuhide TSUJI

出版者

The Institute of Electronics, Information and Communication Engineers

雑誌

IEICE TRANSACTIONS on Electronics (ISSN:09168516)

巻号頁・発行日

vol.E105-C, no.11, pp.644-651, 2022-11-01

---

This paper shows structural optimal design of optical waveguide components utilizing an efficient 3D frequency-domain and 2D time-domain beam propagation method (BPM) with an alternating direction implicit (ADI) scheme. Usual optimal design procedure is based on iteration of numerical simulation, and total computational cost of the optimal design mainly depends on the efficiency of numerical analysis method. Since the system matrices are tridiagonal in the ADI-based BPM, efficient analysis and optimal design are available. Shape and topology optimal design shown in this paper is based on optimization of density distribution and sensitivity analysis to the density parameters. Computational methods of the sensitivity are shown in the case of using the 3D semi-vectorial and 2D time-domain BPM based on ADI scheme. The validity of this design approach is shown by design of optical waveguide components: mode converters, and a polarization beam splitter.

著者

Kei FUJIMOTO Masashi KANEKO Kenichi MATSUI Masayuki AKUTSU

出版者

The Institute of Electronics, Information and Communication Engineers

雑誌

IEICE TRANSACTIONS on Communications (ISSN:09168516)

巻号頁・発行日

vol.E105-B, no.5, pp.522-532, 2022-05-01

被引用文献数

4

---

Packet processing on commodity hardware is a cost-efficient and flexible alternative to specialized networking hardware. However, virtualizing dedicated networking hardware as a virtual machine (VM) or a container on a commodity server results in performance problems, such as longer latency and lower throughput. This paper focuses on obtaining a low-latency networking system in a VM and a container. We reveal mechanisms that cause millisecond-scale networking delays in a VM through a series of experiments. To eliminate such delays, we design and implement a low-latency networking system, kernel busy poll (KBP), which achieves three goals: (1) microsecond-scale tail delays and higher throughput than conventional solutions are achieved in a VM and a container; (2) application customization is not required, so applications can use the POSIX sockets application program interface; and (3) KBP software does not need to be developed for every Linux kernel security update. KBP can be applied to both a VM configuration and a container configuration. Evaluation results indicate that KBP achieves microsecond-scale tail delays in both a VM and a container. In the VM configuration, KBP reduces maximum round-trip latency by more than 98% and increases the throughput by up to three times compared with existing NAPI and Open vSwitch with the Data Plane Development Kit (OvS-DPDK). In the container configuration, KBP reduces maximum round-trip latency by 21% to 96% and increases the throughput by up to 1.28 times compared with NAPI.

著者

Marimo MATSUMOTO Masaya TAMURA

出版者

The Institute of Electronics, Information and Communication Engineers

雑誌

IEICE TRANSACTIONS on Electronics (ISSN:09168516)

巻号頁・発行日

vol.E105-C, no.9, pp.398-406, 2022-09-01

被引用文献数

2

---

Couplers in a film-type capacitive wireless power charging (CWC) system for an implantable medical device were designed and analyzed in this work. Due to the high conductivity of the human body, two paths contribute to the power transmission, namely a high-frequency current and an electric field. This was confirmed by an equivalent circuit of the system. During analysis of the system, we used pig skin with subcutaneous fat, which has a high affinity with the human body, to search for a highly efficient electrode shape. Subsequently, we fabricated the designed coupler and measured ηmax. An ηmax of 56.6% was obtained for a half-circular coupler with a radius of 20 mm and a distance of 10 mm between adjacent couplers. This study will contribute to the realization of implantable devices that can be recharged during breaks or while sleeping at home and is expected to significantly reduce the burden on patients.

著者

Akihiro YOSHITAKE Masaharu TAKAHASHI

出版者

The Institute of Electronics, Information and Communication Engineers

雑誌

IEICE TRANSACTIONS on Communications (ISSN:09168516)

巻号頁・発行日

vol.E105-B, no.7, pp.848-855, 2022-07-01

---

Currently, wireless power transmission technology is being developed for capsule endoscopes. By removing the battery, the capsule endoscope is miniaturized, the number of images that can be taken increases, and the risk of harmful substances leaking from the battery when it is damaged inside the body is avoided. Furthermore, diagnostic accuracy is improved by adjusting the directivity of radio waves according to the position of the capsule endoscope to improve efficiency and adjusting the number of images to be taken according to position by real-time position estimation. In this study, we report the result of position estimation in a high-definition numerical human body model and in an experiment on an electromagnetic phantom.

著者

Fumihiro CHINA Naoki TAKEUCHI Hideo SUZUKI Yuki YAMANASHI Hirotaka TERAI Nobuyuki YOSHIKAWA

出版者

The Institute of Electronics, Information and Communication Engineers

雑誌

IEICE TRANSACTIONS on Electronics (ISSN:09168516)

巻号頁・発行日

vol.E105-C, no.6, pp.264-269, 2022-06-01

---

The adiabatic quantum flux parametron (AQFP) is an energy-efficient, high-speed superconducting logic device. To observe the tiny output currents from the AQFP in experiments, high-speed voltage drivers are indispensable. In the present study, we develop a compact voltage driver for AQFP logic based on a Josephson latching driver (JLD), which has been used as a high-speed driver for rapid single-flux-quantum (RSFQ) logic. In the JLD-based voltage driver, the signal currents of AQFP gates are converted into gap-voltage-level signals via an AQFP/RSFQ interface and a four-junction logic gate. Furthermore, this voltage driver includes only 15 Josephson junctions, which is much fewer than in the case for the previously designed driver based on dc superconducting quantum interference devices (60 junctions). In measurement, we successfully operate the JLD-based voltage driver up to 4 GHz. We also evaluate the bit error rate (BER) of the driver and find that the BER is 7.92×10-10 and 2.67×10-3 at 1GHz and 4GHz, respectively.

著者

Chongyu YU Jun FENG

出版者

The Institute of Electronics, Information and Communication Engineers

雑誌

IEICE TRANSACTIONS on Electronics (ISSN:09168516)

巻号頁・発行日

vol.E105-C, no.5, pp.184-193, 2022-05-01

---

A linear and broadband power amplifier (PA) for 5G phased-array is presented. The design improves the linearity by operating the transistors in deep class AB region. The design broadens the bandwidth by applying the inter-stage weakly-coupled transformer. The theory of transformers is illustrated by analyzing the odd- and even-mode model. Based on this, the odd-mode Q factor is used to evaluate the quality of impedance matching. Weakly- and strongly-coupled transformers are compared and analyzed in both the design process and applicable characteristics. Besides, a well-founded method to achieve the transformer-based balanced-unbalanced transformation is proposed. The fully integrated two-stage PA is designed and implemented in a 65-nm CMOS process with a 1-V power supply to provide a maximum small-signal gain of 19dB. The maximum output 1-dB compressed power (P1dB) of 17.4dBm and the saturated output power (PSAT) of 18dBm are measured at 28GHz. The power-added efficiency (PAE) of the P1dB is 26.5%. From 23 to 32GHz, the measured P1dB is above 16dBm, covering the potential 5G bands worldwide around 28GHz.

著者

Katsuki TOKANO Wenqi ZHU Tatsuki OSATO Kien NGUYEN Hiroo SEKIYA

出版者

The Institute of Electronics, Information and Communication Engineers

雑誌

IEICE TRANSACTIONS on Communications (ISSN:09168516)

巻号頁・発行日

vol.E105-B, no.5, pp.494-503, 2022-05-01

被引用文献数

4

---

This paper presents a design method of a two-hop wireless power transfer (WPT) system for installing on a robot arm. The class-E inverter and the class-D rectifier are used on the transmission and receiving sides, respectively, in the proposed WPT system. Analytical equations for the proposed WPT system are derived as functions of the geometrical and physical parameters of the coils, such as the outer diameter and height of the coils, winding-wire diameter, and number of turns. Using the analytical equations, we can optimize the WPT system to obtain the design values with the theoretically highest power-delivery efficiency under the size limitation of the robot arm. The circuit experiments are in quantitative agreement with the theoretical predictions obtained from the analysis, indicating the validity of the analysis and design method. The experimental prototype achieved 83.6% power-delivery efficiency at 6.78MHz operating frequency and 39.3W output power.

著者

Ryota ISHIBASHI Takuma TSUBAKI Shingo OKADA Hiroshi YAMAMOTO Takeshi KUWAHARA Kenichi KAWAMURA Keisuke WAKAO Takatsune MORIYAMA Ricardo OSPINA Hiroshi OKAMOTO Noboru NOGUCHI

出版者

The Institute of Electronics, Information and Communication Engineers

雑誌

IEICE TRANSACTIONS on Communications (ISSN:09168516)

巻号頁・発行日

vol.E105-B, no.4, pp.364-378, 2022-04-01

被引用文献数

2

---

To sustain and expand the agricultural economy even as its workforce shrinks, the efficiency of farm operations must be improved. One key to efficiency improvement is completely unmanned driving of farm machines, which requires stable monitoring and control of machines from remote sites, a safety system to ensure safe autonomous driving even without manual operations, and precise positioning in not only small farm fields but also wider areas. As possible solutions for those issues, we have developed technologies of wireless network quality prediction, an end-to-end overlay network, machine vision for safety and positioning, network cooperated vehicle control and autonomous tractor control and conducted experiments in actual field environments. Experimental results show that: 1) remote monitoring and control can be seamlessly continued even when connection between the tractor and the remote site needs to be switched across different wireless networks during autonomous driving; 2) the safety of the autonomous driving can automatically be ensured by detecting both the existence of people in front of the unmanned tractor and disturbance of network quality affecting remote monitoring operation; and 3) the unmanned tractor can continue precise autonomous driving even when precise positioning by satellite systems cannot be performed.

著者

Jun SHIBAYAMA Takuma KURODA Junji YAMAUCHI Hisamatsu NAKANO

出版者

The Institute of Electronics, Information and Communication Engineers

雑誌

IEICE TRANSACTIONS on Electronics (ISSN:09168516)

巻号頁・発行日

vol.E105-C, no.4, pp.159-162, 2022-04-01

---

A periodic array of InSb spheres on a substrate is numerically analyzed at terahertz frequencies. The incident field is shown to be coupled to the substrate due to the guided-mode resonance. The effect of the background refractive index on the transmission characteristics is investigated for sensor applications.

著者

Thanh Binh NGUYEN Naobumi MICHISHITA Hisashi MORISHITA Teruki MIYAZAKI Masato TADOKORO

出版者

The Institute of Electronics, Information and Communication Engineers

雑誌

IEICE TRANSACTIONS on Communications (ISSN:09168516)

巻号頁・発行日

vol.E105-B, no.3, pp.275-284, 2022-03-01

被引用文献数

1

---

We developed a mantle-cloak antenna by controlling the surface reactance of a dielectric-loaded dipole antenna. First, a mantle-cloak antenna with an assumed ideal metasurface sheet was designed, and band rejection characteristics were obtained by controlling the surface reactance of the mantle cloak. The variable range of the frequency spacing between the operating and stopband frequencies of the antenna was clarified by changing the value of the surface reactance. Next, a mantle-cloak antenna that uses vertical strip conductors was designed to clarify the characteristics and operating principle of the antenna. It was confirmed that the stopband frequency was 1130MHz, and the proposed antenna had a 36.3% bandwidth (|S11| ≤ -10dB) from 700 to 1010MHz. By comparing the |S11| characteristics and the input impedance characteristics of the proposed antenna with those of the dielectric-loaded antenna, the effect of the mantle cloak was confirmed. Finally, a prototype of the mantle-cloak antenna that uses vertical strip conductors was developed and measured to validate the simulation results. The measurement results were consistent with the simulation results.