著者

佐藤 運海 竹ノ内 敏一 田中 博志 若林 信一 佐藤 元太郎

出版者

公益社団法人精密工学会

雑誌

精密工学会誌論文集 (ISSN:13488724)

巻号頁・発行日

vol.70, no.12, pp.1510-1515, 2004-12-05

被引用文献数

10 6 6

---

This paper describes the elucidation about influence of dilute NaCl electrolyzed water on character of Al-Mg alloy cutting surface. First, the immersing experiment was conducted for cutting sample of Al-Mg alloy A5056B on the electrolyzed reduced water and electrolyzed oxidized water of 0.10wt% NaCl. Next, checked whether discoloration had occurred on sample surface, and analyzed the element distribution and chemical bond state on cutting surface by ASE (Auger Electron Spectroscopy) and ESCA (Electron Spectroscopy for Chemical Analysis). As results of the study, following could be identified. (1) Dilute NaCl electrolyzed water can be applied to processes, such as machining and surface treatment of Al-Mg alloy. (2) The element distribution of the Al-Mg alloy on cutting surface is controllable by dilute NaCl electrolyzed water. (3) The chemical bond state of aluminum element on Al-Mg alloy cutting surface is controllable by dilute NaCl electrolyzed water.

著者

竹ノ内 敏一 田中 博志 若林 信一

出版者

一般社団法人 表面技術協会

雑誌

表面技術 (ISSN:09151869)

巻号頁・発行日

vol.54, no.11, pp.818-822, 2003 (Released:2004-11-19)

参考文献数

6

被引用文献数

8 8

---

Electrolyzed alkaline water, obtained by the electrolysis of a dilute NaCl solution in a cathode compartment shows high pH (alkalinity), low ORP (Oxidation Reduction Potential), and moderate reducibility and oil-emulsification. By utilizing the characteristics of the alkalinity and the oil-emulsification of the electrolyzed alkaline water, metals and lead frames stamped with oil were washed and cleaned, then the cleanness of metals and lead frames for electronic products was evaluated. The surface analysis and quantitative data on remaining residual oils and ionic contamination, AES (Auger Electron Spectroscopy) analysis on metals, and wire-bond pull strength on the lead frames which were washed and cleaned by the electrolyzed alkaline water, showed the same level of cleanness compared to that of the conventional cleaning method by chemicals.

著者

佐藤 運海 竹ノ内 敏一 原 宏 山崎 隆夫 若林 信一

出版者

一般社団法人 日本機械学会

雑誌

日本機械学会論文集 C編 (ISSN:03875024)

巻号頁・発行日

vol.71, no.710, pp.3074-3080, 2005-10-25 (Released:2011-03-04)

参考文献数

7

被引用文献数

8 8

---

This paper describes development of end milling of carbon steel by electrolyzed reduced water of dilute sodium chloride solution, instead of conventional cutting with cutting fluid which is not environmentally consciousness. First, experimental equipments were built with a machining center, cutting fluid supply system made from the bath pump, temperature sensor and temperature recorder etc., and end milling processing of carbon steel was performed using electrolyzed reduced water of dilute sodium chloride solution and conventional cutting fluid respectively. Next, measured surface roughness, evaluated surface deterioration layer, temperature change of work piece and wear state of end milling. As the results of all evaluations above-mentioned, there is no difference between the end milling process using electrolyzed reduced water and that of conventional using cutting fluid. It is supposed electrolyzed reduced water instead of cutting fluid is environmentally consciousness process.

著者

竹内 由美 若林 信一

出版者

公益社団法人日本分析化学会

雑誌

分析化学 (ISSN:05251931)

巻号頁・発行日

vol.39, no.7, pp.T99-T106, 1990-07-05

被引用文献数

1

---

タングステンメタライズ-アルミナ界面のガラス相の選択分析法について検討した.試料のタングステンメタライズをはく離し, ガラス相を露出させた後, (1+5)硫酸により200℃, 1.5時間の加圧酸分解を行うことによりガラス相のみの選択溶解が可能であった.そこで試料と同一濃度の硫酸及び標準的な試料に含まれるAl, Si, Mg, Caを加えた標準液を用いてICP-AESで分析を行った.その結果溶出量としてサンプル当たり±0.1mg, 組成比としてAl_2O_3,SiO_2が±1wt%, MgO, CaOが±0.5wt%の精度でメタライズ中に浸透したガラス量及び組成の評価が可能となった.