著者

田中 祐人 酒谷 哲 野口 孝俊

出版者

社団法人 日本鋼構造協会

雑誌

鋼構造論文集 (ISSN:18809928)

巻号頁・発行日

vol.18, no.71, pp.71_1-71_13, 2011-09-29 (Released:2012-12-28)

参考文献数

19

---

Jacket structures have many features as follows: a few foundation piles and reduction of site construction period caused by extremely high horizontal rigidity, moreover high manufacturing quality. In the construction of Tokyo International Airport Re-expansion Project, jacket substructures are applied to pile-elevated structures and connecting taxiways. This paper describes structural plan of marine bridges for airplanes, moreover applicability of jackets for substructures to marine bridges for airplanes.

著者

松井 英治 最上 公彦 木村 衛

出版者

社団法人 日本鋼構造協会

雑誌

鋼構造論文集 (ISSN:18809928)

巻号頁・発行日

vol.1, no.3, pp.115-127, 1994-09-30 (Released:2010-06-28)

参考文献数

6

---

A Cable-Reinforced Membrane Structures with Glulam Arches was constructed as the Hakuryu Dome in Daiwa-cho, Hiroshima Prefecture. This structure was realized by solving the following three issues.(1)Establisliment of methods of Cablenet design and construction(2)Development of Membrane joint detail which hides joint lines to show the roof as one Membrane(3)Establishment of design formula and construction method of Glued Laminated Timber joint, the Big Finger Joint, which doesn't use steel connections.This report describes the proposed design methods and the erection of the Hakuryu Dome.

著者

城戸 將江 福元 敏之 津田 惠吾 一戸 康生 森田 耕次

出版者

社団法人 日本鋼構造協会

雑誌

鋼構造論文集 (ISSN:18809928)

巻号頁・発行日

vol.24, no.94, pp.94_49-94_64, 2017-06-27 (Released:2018-07-06)

参考文献数

21

---

It is an urgent issue to formulate a design method for concrete filled steel tubular structures against the long duration earthquake. This report shows the results of the study and research about the cyclic rotation capacity of the square concrete filled steel tubular columns against the long period ground motion. The experimental results by previous studies and this committee are introduced and the outlines of the fatigue properties of square CFT columns subjected to the axial force and cyclic lateral loading with constant deformation are given.

著者

岡本 達雄 福山 国夫 東端 泰夫 土田 伸治 半田 健二 益尾 潔

出版者

社団法人 日本鋼構造協会

雑誌

鋼構造論文集 (ISSN:18809928)

巻号頁・発行日

vol.3, no.10, pp.7-19, 1996-06-28 (Released:2011-03-01)

参考文献数

8

被引用文献数

2

---

The 1995 Hyogoken-Nanbu Earthquake attacked Kobe on January 17, 1995 and brought us the huge destruction. At the IKUTA shrine, a lot of buildings were damaged and the Hall of Worship fell down completely. In the ruins, the superior priest of the shrine requested us to restore the buildings as soon as possible to encourage citizens of Kobe. Then reconstruction of the shrine started on January 22, 1995. The progressive technology to give the buildings sufficient seismic resistant capability is intended. For the columns of the new Hall of Worship, CFT(Concrete Filled steel Tube) is used, and the concrete which compressive strength is 160 NJmm2, is filled into the tube. The reconstruction procedure of the new Hall will be reported herein.

著者

林 和宏 岡崎 太一郎 林 旭川 中島 正愛

出版者

社団法人 日本鋼構造協会

雑誌

鋼構造論文集 (ISSN:18809928)

巻号頁・発行日

vol.21, no.82, pp.82_39-82_50, 2014-06-24 (Released:2015-08-29)

参考文献数

15

---

A design detail of beam-to-column connections is developed for previously proposed built-up column member comprising high-strength H-SA700 steel connecting to conventional-steel beams. In the design concept, the beams are allowed to develop plasticity during the large earthquakes, while the built-up column remains elastic. A bolted connection detail, consisting of steel end plates and high tension bolts, is adapted to connect the beams to the joints. Experiments were conducted to examine the seismic performance of the beam-to-column connections with the built-up column. Test results show that additional T-shape stiffeners were needed at the beam-to-column connections to provide appropriate rigidity of the joint to ensure the yielding of the beams.

著者

河野 昭雄 田中 秀宣 伊藤 倫夫

出版者

社団法人 日本鋼構造協会

雑誌

鋼構造論文集

巻号頁・発行日

vol.10, no.40, pp.45-52, 2003

---

This investigation is carried out to clear the difference of lateral stiffness of rahmen frame due to various methods for elastic rotation stiffness of steel exposed-type column base . At first, a new formula for elastic rotation stiffness of steel exposed-type column base considered column axial force and concrere stiffness under base-plate is suggested. It is compared and discussed that lateral stiffness of rahmen frame by nonlinear elastic analysis using the suggested formula compared with the result by conventional elastic analysis using the formula by Architectural Institute of Japan.

著者

内田 大介 森 猛 佐々木 雄一

出版者

社団法人 日本鋼構造協会

雑誌

鋼構造論文集 (ISSN:18809928)

巻号頁・発行日

vol.23, no.89, pp.89_51-89_58, 2016-03-25 (Released:2017-03-22)

参考文献数

6

---

Various studies have been performed on improving fatigue strength of out-of-plane gusset welded joints because their fatigue strength is very low in the case of as-welded condition. Grinding the weld toes of the joints with burr grinder is the most common method for fatigue strength enhancement. In this study, for the purpose of sugesting appropriate grinding depth for out-of-plane gusset joints, fatigue tests and FEM analyses have been performed.

著者

鈴木 孝夫

出版者

Japanese Society of Steel Construction

雑誌

鋼構造論文集 (ISSN:18809928)

巻号頁・発行日

vol.1, no.1, pp.87-94, 1994-03-31 (Released:2010-06-28)

---

This paper describes the summary of structural design method and construction procedures of ″Edo-Tokyo Museum″ constructed at Ryogoku site, Tokyo, in march 1993. The unique outlook of the building is derived from the origin of Japanese trailitional housing style. In order to make such unique design realize, several new procedures and consept have been developed. One of the important elements for the construct ion process is welding procedure for the steel joint. As the most reasonable and real istic method, field electroslag welding method was newly adopted.

著者

松井 繁憲 寺西 功 三田 哲也 藤野 陽三

出版者

Japanese Society of Steel Construction

雑誌

鋼構造論文集 (ISSN:18809928)

巻号頁・発行日

vol.2, no.7, pp.63-71, 1995-09-30 (Released:2011-07-04)

参考文献数

10

被引用文献数

1

---

For reconsideration of the corrosion protect at the interior of a steel box girder we reserch a corrosion environment of the interior of a steel box girder at Hakucho Bridge (at Hokkaido). This bridge i s composed of two box girders of which the interior as well as the exterior was not painted on the basis of the local design specifications. In one of the two box girders, a dehumidification plant was installed and has been operated for one and half year. We report about the experiment, and measurements of a temperature and a humidity, a working condition of the dehumidifier, an example of ACM corrosion sensor's output.

著者

田畑 晶子 金治 英貞 黒野 佳秀 山口 隆司

出版者

一般社団法人 日本鋼構造協会

雑誌

鋼構造論文集 (ISSN:18809928)

巻号頁・発行日

vol.20, no.79, pp.79_19-79_28, 2013-09-27 (Released:2014-12-20)

参考文献数

10

---

The authors focused on the high strength bolted friction grip joints with countersunk head bolts which can finish the surface of the connection plate flat smoothly and prevent from functional depression due to corrosion. In this study, we carried out FE analysis varying the angle of countersunk head in order to evaluate the contact pressure of double shear connected friction joints with countersunk heads. Also, we have investigated the influence on load transferring mechanism by using countersunk head bolt for frictional joints. It has concluded that the most desirable angle of the countersunk head is 90 degrees. CD series's slip strength is about only 4% lower than that with normal head bolts.

著者

宮内 賢治 山田 大彦

出版者

Japanese Society of Steel Construction

雑誌

鋼構造論文集 (ISSN:18809928)

巻号頁・発行日

vol.14, no.55, pp.37-46, 2007-09-25 (Released:2010-06-28)

参考文献数

8

---

The purpose of present study is to propose the approximate technique taking deflection of foundation girders and pile-soil into consideration for structural analysis. Separation of the upper structure from the pile-soil structure is the practical method in case of structural frames with foundation girders constructed from reinforced concrete of high stiff ness, but it isn't a general method in case of foundation girders of finite rigidity. In the pres ent analysis, two approximations are applied, and those enable to separate the analysis of the upper structure from that of the pile-soil structure. This is proposed as a new approximation method of rotation-rigidity.

著者

廣畑 幹人 寺口 大輝 北根 安雄

出版者

一般社団法人 日本鋼構造協会

雑誌

鋼構造論文集 (ISSN:18809928)

巻号頁・発行日

vol.26, no.101, pp.101_79-101_86, 2019-03-25 (Released:2020-03-12)

参考文献数

13

---

For investigating effect of heating and cooling process simulating fire on mechanical properties of Steels for Bridge High Performance Structure (SBHS), a series of experiment was carried out. The heating of 600℃ did not change the mechanical properties of SBHS from those without heating and cooling. The heating of 900℃ and air cooling decreased the mechanical properties of SBHS due to softening. The heating of 900℃ and water cooling increased the ultimate strength due to hardening; however, it decreased the yield stress and elongation of SBHS to the level below that required by JIS.

著者

松本 毅 米澤 栄二 沖田 斉 マディアッタ・ンデレ ・ブーバ カロンボ・ ムケバ

出版者

社団法人 日本鋼構造協会

雑誌

鋼構造論文集 (ISSN:18809928)

巻号頁・発行日

vol.24, no.93, pp.93_93-93_105, 2017

---

<p>The Matadi Bridge, a suspension bridge in Democratic Republic of Congo, was completed in May 1983 by the Japanese ODA. The inspection facilities such as the under girder inspection vehicles, the inside girder inspection vehicles, are equipped on this bridge. As the bridge have been opened to the public for nearly 30 years, these maintenance vehicles need to be improved because some deteriorations and the consequent problems have been found and reported by OEBK which maintains the bridge. JICA(Japan International Cooperation Agency) dispatched experts to solve these problems and repaired the inspection vehicles at the site in cooperation with OEBK. This paper reports the improvement activities done by JICA Study Team.</p>

著者

森脇 良一 林 健治

出版者

Japanese Society of Steel Construction

雑誌

鋼構造論文集 (ISSN:18809928)

巻号頁・発行日

vol.2, no.8, pp.1-12, 1995-12-28 (Released:2010-06-28)

参考文献数

17

---

In order to establish the ultimate state design, it should be veri fied the mechanical properties of tension members as well as compression members in the ultimate state. In this paper, resting on this viewpoint, tension tests on notched plates were carried out to investigate the influence of mechanical properties of materials and stress concentration on the plastic deformation capacity, and to clarify the mecanical characteristics of tension members. And a practical formula is proposed to evaluate the plastic deformation capacity of tension members. Moreover, it is also clarified the parameter to control the plastic deformation fields of tension members in the ultimate state.

著者

松本 毅 村瀬 佐太美 池田 定三 中西 治

出版者

社団法人 日本鋼構造協会

雑誌

鋼構造論文集 (ISSN:18809928)

巻号頁・発行日

vol.6, no.22, pp.29-39, 1999

---

下津井瀬戸大橋は瀬戸大橋の最も北側に位置する吊橋で、本州の倉敷市下津井とその南にある櫃石島(ひついしじま)とを結んでいる。下津井瀬戸大橋には、側径間端部で補剛桁を下から支え、鉛直反力を受け持つピボット構造のエンドリンク4基が設置されている。これらの内のA3エンドリンク(東西各1基、合計2基)ピボット構造部付近から、周辺民家(民家までL=約30m)でも容易に確認できるようなカンカンという大きな金属音が1993年6月頃より発生するようになった。この音の発生は、重量の大きな貨物列車が通過するときに顕著であった。そこで騒音を低減するための応急措置を施した後、1994年1月~2月にかけて、エンドリンクの精密点検を行い音源調査、ひずみ・変位調査等を現地に於いて実施した。'94年度には、騒音源と思われるピボット部へ潤滑剤を注入するための孔明け方法を検討するために模型実験を行った。また、ピボット部に注入すべき潤滑剤の選定を行った。これらの調査、実験の成果を用いて、'95年度にA3エンドリンクの補修工事を行い、騒音を解消することができた。また'96年度にはA4エンドリンクを同様の方法で補修した。ここでは、エンドリンクの精密点検及び補修工事について述べる。

著者

作本 好文 千々岩 力雄

出版者

Japanese Society of Steel Construction

雑誌

鋼構造論文集 (ISSN:18809928)

巻号頁・発行日

vol.1, no.1, pp.25-40, 1994-03-31 (Released:2010-06-28)

参考文献数

21

被引用文献数

1

---

This paper reports on the studies concerning Fire Resistant steel for building construction, both in the aspect of steelmaking in the development of steel products and in the aspect of high-temperature strength properties of steel products, joints (high-strength bolts) and structural members, while illustrating the usefulness of Fire Resistant steel by citing an example of a fire-safe design of a high-rise building using Fire Resistant steel without fire protection.

著者

脇山 広三 金 振鎬 多田 元英

出版者

Japanese Society of Steel Construction

雑誌

鋼構造論文集 (ISSN:18809928)

巻号頁・発行日

vol.2, no.5, pp.53-58, 1995-03-31 (Released:2010-06-28)

参考文献数

8

---

Fatigue fracture or delayed fracture often occurs at the threaded portion or the underhead fillet of high-strength bolts where the stress concentrates. In order to reduce the stress-concentration at the threaded portion, we have already proposed the improved thread shape. In this paper, the cone shape head is proposed to reduce the stress-concentration at the underhead fillet. The efficiency of this shape is analyzed by the FEM in which the parameters are the radius of the fillet and the angle of the bearing surface at the underhead.

著者

小松 靖朋 中上 貴裕 柚本 真介 小林 茂 松本 崇志 山口 隆司

出版者

社団法人 日本鋼構造協会

雑誌

鋼構造論文集 (ISSN:18809928)

巻号頁・発行日

vol.22, no.85, pp.85_1-85_14, 2015-03-25 (Released:2016-05-18)

参考文献数

12

---

In order to repair and retrofit the aged metal bridge, it is important to undestand the mechanical behavior of aged steel and replacement of rivet to H.T.B. In this study, firstly, tensile loading tests, chemical tests of aged steel are conducted to understand the basic property of aged steel. Secondly, tensile loading tests for multi-bolted joint are conducted to clarify replacement of rivet to H.T.B. In this study, three specimens are fabricated and tested; all riveted joint, partially H.T.B replaced, and, fully H.T.B replaced. Based on the test results, it is found that load carrying capacity and deformability of partially and fully replaced to H.T.B can be improved due to adding frictional resistance comparing with riveted joints only.

著者

松井 千秋

出版者

Japanese Society of Steel Construction

雑誌

鋼構造論文集 (ISSN:18809928)

巻号頁・発行日

vol.1, no.2, pp.11-24, 1994-06-30 (Released:2010-06-28)

参考文献数

30

被引用文献数

5

---

The present situations of design and construction on concrete filled steel tubular structures in Japan are described. The outlines of research works conducted in Kyushu University, such as the elasto-plastic behaviors of frames, the ultimate strength and deformation capacity of members, the limiting values of width(diameter)-tothickness ratio of cross sections, the stability and strength of slender columns, and the behaviors of truss frames are discussed. The design strengths of columns based on several foreign design standards are compared with Japanese design strength.

著者

許斐 信三 前原 智

出版者

社団法人 日本鋼構造協会

雑誌

鋼構造論文集 (ISSN:18809928)

巻号頁・発行日

vol.1, no.3, pp.45-56, 1994

---

The roof frame of THE FUKUOKA EXIBITION HALL that images sea waves is composed by the large scaled steel latiticed vault and the steel trussed ribs which strengthen the vaulted shell and are utilized as maintenance roots and mechanical uses. Prestressing forces has been introduced to the edge beams of the steel vault to reduce vertical displacement. The designmethods for the metal prestressing shell structure adopted here, the effect of prestressing and the steel trussed ribs, and so on are presented in this paper.