著者
梅田 純子 高田 龍一 道浦 吉貞 近藤 勝義
出版者
一般社団法人 スマートプロセス学会 (旧高温学会)
雑誌
スマートプロセス学会誌 (ISSN:2186702X)
巻号頁・発行日
vol.3, no.5, pp.323-327, 2014-09-20 (Released:2015-08-01)
参考文献数
5
被引用文献数
2

Rice husks, one of the typical agricultural wastes, consist with 70-75 mass% of organics and 15-20 mass% of amorphous silica. Silica can be obtained by combusting rice husks in air. However, silica purity is reduced by metallic impurities contained in rice husks. To extract high-purity amorphous silica from rice husks, the citric acid leaching process was developed to remove the metallic impurities from rice husks. By optimizing the citric acid solution concentration and combustion temperature of rice husks, completely amorphous silica ashes with 99.5 mass% were obtained. To establish the large-scale equipment to produce high purity amorphous rice husk silica, the process parameters in the citric acid leaching and air combustion were optimized. There was no significant difference of silica purity and the impurity contents of rice husk ashes by using between small-scale and large-scale equipment. Citric acid leached rice husk ashes were employed as the reinforcements of concrete materials. Compressive strength in use of high-purity amorphous silica revealed a higher value compared to the use of silica fume and raw rice husk ashes. The effect of citric acid leached rice husk ashes was high pozzolanic reactivity due to high-purity amorphous silica particles and the large surface area due to their porous structures.
著者
梅田 純子 三本 嵩哲 今井 久志 近藤 勝義
出版者
一般社団法人 粉体粉末冶金協会
雑誌
粉体および粉末冶金
巻号頁・発行日
vol.64, no.2, pp.81-87, 2017

訂正<BR><BR><p>本誌,第63巻第12号(2016)1002-1008頁に掲載された論文は,著者修正前の原稿で誤って掲載されました.著者より修正の申し出がありました.修正後の論文をここに改めて全文掲載します.</p>
著者
梅田 純子 近藤 勝義 道浦 吉貞
出版者
一般社団法人 廃棄物資源循環学会
雑誌
廃棄物学会研究発表会講演論文集 第18回廃棄物学会研究発表会
巻号頁・発行日
pp.129, 2007 (Released:2007-11-23)

籾殻に含まれる可溶性シリカ成分を非晶質構造の状態で抽出すべく,無機強酸により籾殻を酸洗浄処理した後,600~1200℃で大気焼成した.その際にX線回折により結晶化温度を把握すると同時に,焼成灰中のシリカ純度およびアルカリ金属不純物量に及ぼす酸処理条件の影響を調査した.その結果,籾殻の約70%を示す炭水化物(セルロースやヘミセルロース)は酸処理過程で加水分解することを熱分解ガスクロマトグラフ質量分析によって明らかにした.例えば,加水分解によってセルロースはレボグルコサンを,ヘミセルロースはフラフルールをそれぞれ生成する.
著者
祖父尼 淳 森安 史典 佐野 隆友 藤田 充 糸川 文英 土屋 貴愛 辻 修二郎 石井 健太郎 池内 信人 鎌田 健太郎 田中 麗奈 梅田 純子 殿塚 亮祐 本定 三季 向井 俊太郎 糸井 隆夫
出版者
一般社団法人 日本膵臓学会
雑誌
膵臓 (ISSN:09130071)
巻号頁・発行日
vol.30, no.2, pp.199-209, 2015-04-20 (Released:2015-05-08)
参考文献数
18

High intensity focused ultrasound(HIFU)治療は,その超音波発信源を多数取り付けた発信源から超音波を腫瘍の目的部位の1点に集束させ,体外から組織の焼灼を行う治療法である.焦点領域のみを80~100度に加熱し,熱エネルギーおよびキャビテーションの作用により組織を凝固壊死させ,焦点領域以外の介在組織にはほとんど影響を与えないという治療法である.われわれは切除不能膵癌に対するHIFU治療の安全性と有効性を検証するため,Yuande Bio-Medical Engineering社のFEP-BY02 HIFU Systemを用いて臨床試験を2008年12月より行った.膵癌に対するHIFU治療は問題点もあり,さらなる検討や症例の蓄積が必要であるが,われわれの検討では切除不能膵癌に対し安全にHIFU治療を行うことが可能であり,今後,予後不良な膵癌への低侵襲治療のひとつとなりうる可能性が示唆された.
著者
梅田 純子 近藤 勝義 道浦 吉貞
出版者
一般社団法人 廃棄物資源循環学会
雑誌
廃棄物学会研究発表会講演論文集
巻号頁・発行日
vol.18, pp.129, 2007

籾殻に含まれる可溶性シリカ成分を非晶質構造の状態で抽出すべく,無機強酸により籾殻を酸洗浄処理した後,600~1200℃で大気焼成した.その際にX線回折により結晶化温度を把握すると同時に,焼成灰中のシリカ純度およびアルカリ金属不純物量に及ぼす酸処理条件の影響を調査した.その結果,籾殻の約70%を示す炭水化物(セルロースやヘミセルロース)は酸処理過程で加水分解することを熱分解ガスクロマトグラフ質量分析によって明らかにした.例えば,加水分解によってセルロースはレボグルコサンを,ヘミセルロースはフラフルールをそれぞれ生成する.
著者
早場 亮一 田邊 由紀子 米澤 隆行 梅田 純子 近藤 勝義
出版者
一般社団法人 日本機械学会
雑誌
日本機械学会論文集 (ISSN:21879761)
巻号頁・発行日
vol.84, no.861, pp.17-00491-17-00491, 2018 (Released:2018-05-25)
参考文献数
30

Stents are one of devices for the invasive cardiac catheterization (Percutaneous Transluminal Coronary Angioplasty) and especially for pediatric catheterization, the stent is manufactured by superelastic alloys including TiNi alloy. Transradial coronary intervention (TRI) is an invasive treatment in comparison with transfemoral coronary intervention (TFI), as TRI can reduce the risk of bleeding complications. To perform TRI, it is necessary to reduce the thickness of stent and diameters of delivery system. Therefore, one of the solution is to improve the strength of the materials for the stent. In this study, the medical application to stents was investigated by manufacturing high-strengthened Ni-rich powder metallurgy TiNi alloy using pure Ti powder and pure Ti pre-mixed powder. Ni-rich TiNi shape memory alloys showed much high plateau stress and enough shape recovery rate compared to the conventional ingot metallurgy TiNi alloy used in the commercial stent devices. In the simulation of the stent radial force by a finite element analysis (FEA), it was clarified that the radial forces of Ti-52.0 at.%Ni (stent wall thickness; 80 μm) and Ti-50.5 at.%Ni (stent wall thickness; 200 μm) were equivalent. The improvement of plateau stress of TiNi alloys successfully reduced the thickness of the stent by 120 μm (60 %). In fact, the stent using Ni-rich TiNi alloy resulted in the thinned stent with a high radial expansion force. When implanting the stents made of Ni-rich TiNi alloy into the external iliac artery of pigs, no stent fracture was observed, and in-stent occlusion never occurred after 1-month and 3-month placement of the stents. They are similar biocompatibility to commercial stents because of the similar results of inflammation.