著者

遠藤 和人 中川 美加子 肴倉 宏史 井上 雄三 井 真宏 杉原 元一

出版者

公益社団法人 日本材料学会

雑誌

材料 (ISSN:05145163)

巻号頁・発行日

vol.61, no.1, pp.31-36, 2012-01-15 (Released:2012-01-20)

参考文献数

8

被引用文献数

1

---

Necessity to promote a recycle of waste plaster board is mounting, since the waste plaster board has been legally prohibited to dispose into inert landfill site. However, it is concerned that the recycled waste plaster board (recycled gypsum) produces hydrogen sulfide gas, so that it is one of the interference with the recycling. There is a possibility to control the hydrogen sulfide gas production from the recycled gypsum by artificially changing into alkaline condition or adding iron oxide. In this study, we discussed the hydrogen sulfide gas production from a ground improvement with the recycled gypsum, quick lime, and/or iron oxide powder. In addition, unconfined compression strength of the ground improvement is evaluated in order to obtain an incentive of the recycling. Adding only the recycled gypsum cannot improve strength of a soft ground having much amount of fine particles. Quick lime was required for strength improvement. If pH of the ground improvement is greater than 9, it was observed that the hydrogen sulfide gas production potential is negligible. Increasing pH by adding the quick lime is able to more effectively control the production of the hydrogen sulfide gas than adding the iron oxide powder. The production of the hydrogen sulfide gas is able to be controlled by adding the quick lime more than half of the amount of gypsum addition.

著者

進藤 明夫

出版者

公益社団法人 日本材料学会

雑誌

材料 (ISSN:05145163)

巻号頁・発行日

vol.27, no.296, pp.401-415, 1978-05-15 (Released:2009-06-03)

参考文献数

160

著者

中川 憲治 岸田 敬三 谷村 眞治

出版者

公益社団法人 日本材料学会

雑誌

材料 (ISSN:05145163)

巻号頁・発行日

vol.34, no.384, pp.1115-1120, 1985-09-15 (Released:2009-06-03)

参考文献数

45

被引用文献数

1

著者

池田 豊

出版者

公益社団法人 日本材料学会

雑誌

材料 (ISSN:05145163)

巻号頁・発行日

vol.17, no.182, pp.979-989, 1968-11-15 (Released:2009-06-03)

参考文献数

50

被引用文献数

1 1

著者

髙田 潤 中西 真

出版者

公益社団法人 日本材料学会

雑誌

材料 (ISSN:05145163)

巻号頁・発行日

vol.66, no.11, pp.799-803, 2017-11-15 (Released:2017-11-20)

参考文献数

25

著者

宮本 昭彦 村上 敬宜

出版者

公益社団法人 日本材料学会

雑誌

材料 (ISSN:05145163)

巻号頁・発行日

vol.47, no.8, pp.830-835, 1998-08-15 (Released:2009-06-03)

参考文献数

7

被引用文献数

1 1

---

On crime scenes, plate glass is frequently shot by bullets. The fracture of plate glass by a pachinko ball (steel ball) impact also occurs. Experiments were carried out to obtain basic data for estimating the impact velocities of projectiles from the morphology of the fracture. Projectiles {11mm dia. steel balls and 0.38 inch (9mm dia.) lead bullets} were shot onto ordinary glass plates firmly held around a circular periphery.It was assumed that projectile kinetic energy would all be converted into surface energy of fractured glass. The relationship between crack area Af and kinetic energy of projectiles was investigated. A strong experimental correlation was found between Af and the change in kinetic energy. A unique relationship was obtained between crack area and energy consumed during fracture regardless of the projectile material (steel and lead).

著者

北川 浩

出版者

公益社団法人 日本材料学会

雑誌

材料 (ISSN:05145163)

巻号頁・発行日

vol.28, no.307, pp.339-344, 1979-04-15 (Released:2009-06-03)

参考文献数

13

著者

丹羽 雅子

出版者

公益社団法人 日本材料学会

雑誌

材料 (ISSN:05145163)

巻号頁・発行日

vol.22, no.236, pp.383-391, 1973-05-15 (Released:2009-05-26)

参考文献数

37

被引用文献数

1 1

---

In textile industry, performance of the fabrics is still out of the engineering design, because of the difficulty in designing the proper mechanical properties of fabrics, and also of the difficulty in evaluating the performance where the evaluation has been done by a sensory method named "hand-feel" by experts.In this article, recent developments in the theoretical research on the mechanical properties of fabrics are introduced. Theoretical methods of calculating the non-linear property in biaxial and uniaxial tensile deformations of plain woven, plain knitted and inter-lock fabrics are presented here. And bending and shear properties of plain woven fabrics are also dealt with.Furthermore, a new method for evaluating "hand-feel" is introduced; the mechanical properties of fabrics are first characterized and represented by sixteen number of characteristic values obtained by the measurements of mechanical, physical and geometrical properties of the fabrics, and then using a linear model, the "hand-feel" value is calculated from these characteristic values. The agreement between the conventional sensory and the new instrumental methods is demonstrated.

著者

木村 恵雄

出版者

公益社団法人 日本材料学会

雑誌

材料試験 (ISSN:03727971)

巻号頁・発行日

vol.11, no.111, pp.781-785, 1962-12-15 (Released:2009-05-26)

参考文献数

1

---

NIPPON ROCLA PIPE CO. has been producing noncylinder prestressed concrete pipes since the fall of 1961. One of the products which has 1200mm inner diameter and is designed for the inner pressure of 13.0kg/cm2 was tested hydrostatically and under the external load.The results of test obtained are as follows:(1) Under the hydrostatic pressure up to 12.0kg/cm2, there was no leakage on outer surface of the pipe and at rubber joints.As the capacity of the bulkhead of the machine was not sufficiently large, the test up to 13.0kg/cm2 pressure was given up.(2) Under the external load up to 8.25 tons per meter (total load of 33.0 tons), could no visible crack was found at any point of the pipe.From analyses about the stress and measured strain on concrete surface at the end of the pipe, the prestress in the core concrete was supposed to be as much as the designed value, and the flexural strength of the concrete to be sufficient.

著者

吉川 敬治 加藤 寛 星野 光男

出版者

公益社団法人 日本材料学会

雑誌

材料 (ISSN:05145163)

巻号頁・発行日

vol.35, no.399, pp.1431-1437, 1986-12-15 (Released:2009-06-03)

参考文献数

14

---

Hardness of carbon fiber reinforced plastics (CFRP) and Al-2 and 4wt% Cu alloys containing columnar grains was measured with a wedge-shaped indenter, and was compared with their static tensile properties. Hardness measurement was conducted with a Rockwell hardness tester. The hardness and mean pressure of CFRP decreased with the angle θ between indentation normal and fiber direction. The orientation dependences of the hardness and the mean pressure agreed with those of Young's modulus and the fracture strength of CFRP. However, no linear relation existed between the mean pressure and the strength. The hardness and the mean pressure of Al-Cu alloys took a minimum when the angle θ was about π/4 rad, and the orientation dependence of the mean pressure disagreed with those of the yield stress and the ultimate tensile strength. The relation between the mean pressure and the yield stress was described by the equation: σy=(P/3)(0.0017)n, where n is the strain hardening coefficient.

著者

小林 政治郎 山城 貞男 植村 幸生

出版者

公益社団法人 日本材料学会

雑誌

材料 (ISSN:05145163)

巻号頁・発行日

vol.13, no.125, pp.110-116, 1964-02-15 (Released:2009-06-03)

参考文献数

5

---

In this paper, the relations between Charpy impact strength (Absorbed energy/area under notch) and shape of V-notched test bar of unplasticized P.V.C. are described. The results obtained are summarized as follows:(1) Charpy impact strengths are not varied by the deviation of the width, the thickness and the notch angle of test bar in the range of experiment.(2) But they are varied by the deviation of the notch depth and the notch radius.(3) The quantitative values of error of impact strength which are introduced by these deviations are shown on Table I.

著者

小林 昭一

出版者

公益社団法人 日本材料学会

雑誌

材料 (ISSN:05145163)

巻号頁・発行日

vol.27, no.303Appendix, pp.1220-1226, 1978-12-15 (Released:2009-06-03)

著者

篠田 軍治

出版者

公益社団法人 日本材料学会

雑誌

材料試験 (ISSN:03727971)

巻号頁・発行日

vol.5, no.39, pp.738-742, 1956-12-15 (Released:2009-05-26)

参考文献数

14

著者

清木 隆文

出版者

公益社団法人 日本材料学会

雑誌

材料 (ISSN:05145163)

巻号頁・発行日

vol.66, no.11, pp.793-798, 2017

被引用文献数

5

著者

小沢 泉夫 松島 昭吾

出版者

公益社団法人 日本材料学会

雑誌

材料 (ISSN:05145163)

巻号頁・発行日

vol.33, no.371, pp.1114-1121, 1984-08-15 (Released:2009-06-03)

参考文献数

44

著者

下羽 悠一 石川 徹朗 大谷 眞一 秋田 貢一

出版者

公益社団法人 日本材料学会

雑誌

材料 (ISSN:05145163)

巻号頁・発行日

vol.55, no.12, pp.1139-1145, 2006 (Released:2006-12-20)

参考文献数

8

被引用文献数

3 4

---

The X-ray stress measurement based on sin2ψ method has been widely adopted. This technique is not entirely efficient, because it is necessary to measure each diffraction profile one after other at five and more incident X-ray angles. On the other hand, stress measurement based on cosα method was proposed using X-ray film as detector. In this method, the stresses are determined from Debye-ring obtained at a single X-ray incident angle with high efficiency. However, it has the problem in this accuracy on stress determination. In this study, a new stress analyzer with sixteen position sensitive proportional counters (PSPC) radially arranged for incidence X-ray was developed. We examined to determine the plane stress components by multi-regression analysis using sixteen diffraction angles on a Debye-ring. As a result, stress components of σx and τxy were measured with sufficient accuracy. However, a stress of σy had large dispersion, because of low strain sensitivity in the y direction. Moreover, it was clarified that σy had pseud-multicollinearity on multi-regression analysis. The accuracy of σy value itself could not be improved, though an analysis to eliminate an effect of pseud-multicollinearity was carried out. In this paper, we proposed the new method to determine the components using two Debye rings obtained by X-ray incidences in both x and y directions. We tried to measure the residual stress components in the butt welded joint using the method. As a result, it was confirmed that the stresses, σx and σy, were obtained in the sufficient accuracy, and that the shear stress, τxy, was arising near the bond in the welds.

著者

奥田 進

出版者

公益社団法人 日本材料学会

雑誌

材料試験 (ISSN:03727971)

巻号頁・発行日

vol.11, no.109, pp.581-587, 1962-10-15 (Released:2009-05-26)

参考文献数

25

著者

大田 祐太朗 久布白 圭司 山崎 泰広

出版者

公益社団法人 日本材料学会

雑誌

材料 (ISSN:05145163)

巻号頁・発行日

vol.69, no.8, pp.599-604, 2020-08-15 (Released:2020-08-20)

参考文献数

27

被引用文献数

2

---

Ti alloys are widely applied to jet engine components. Low cycle fatigue (LCF) strength of Ti alloys decreases with tensile stress dwell at room temperature (Cold Dwell Fatigue, CDF). CDF strength was influenced by stress level, microstructure, and dwell time. In order to study the effect of long time dwell for CDF properties, LCF test (0s dwell), CDF tests (120s~7200s dwell), and creep test were carried out. With increase of dwell time, fracture cycle decreased and fracture elongation increased. Fracture surface of long time dwell CDF tests corresponded to that of creep test. Additionally, strain accumulations during stress dwell at long time dwell CDF tests were similar to strain change of creep test. From SEM/EBSD analysis, inelastic strain was obviously increased after CDF tests and creep test, compared to LCF test. Hence, it was considered that long time dwell CDF was greatly influenced by creep deformation.

著者

三宅 司朗

出版者

公益社団法人 日本材料学会

雑誌

材料 (ISSN:05145163)

巻号頁・発行日

vol.41, no.464, pp.777-783, 1992-05-15 (Released:2009-06-03)

参考文献数

22

著者

遅沢 浩一郎

出版者

公益社団法人 日本材料学会

雑誌

材料 (ISSN:05145163)

巻号頁・発行日

vol.60, no.7, pp.680-686, 2011-07-15 (Released:2011-07-20)

参考文献数

18

被引用文献数

1 5