著者
Phan Huy Le 田代 真一 湯地 敏史 房野 俊夫 鎌田 憲嗣 田中 学
出版者
一般社団法人 溶接学会
雑誌
溶接学会全国大会講演概要
巻号頁・発行日
vol.2017, pp.376-377, 2017

In this presentation, oxide layer removal process in EP period of AC TIG welding is observed by the high-speed camera. From this experiment, the distribution and velocity of cathode spot are reported.
著者
河合 真二 新堂 正俊 山本 憲吾 永井 卓也 中野 利彦 岡野 成威 望月 正人 菅 哲男
出版者
一般社団法人 溶接学会
雑誌
溶接学会全国大会講演概要
巻号頁・発行日
vol.2015, pp.204-205, 2015

板厚内部の残留応力を実測する手法として、改良型深孔穿孔法(以下、MIRS法:Modified Internal Residual Stress)を開発した。MIRS法には3タイプあり、算出する応力成分数で使い分ける。MIRS法の3タイプの紹介と円筒継手などでの実測例を紹介する
著者
飯田 孝道
出版者
一般社団法人 溶接学会
雑誌
溶接学会誌 (ISSN:00214787)
巻号頁・発行日
vol.62, no.7, pp.508-511, 1993-10-05 (Released:2011-08-05)
参考文献数
3
被引用文献数
7 10
著者
安藤 弘平 長谷川 光雄 豊原 富弘
出版者
一般社団法人 溶接学会
雑誌
鎔接協会誌 (ISSN:18837190)
巻号頁・発行日
vol.11, no.3, pp.75-97, 1941 (Released:2011-08-05)
参考文献数
9

軟鋼の電弧熔接に於けるスパッターリング現象即ち第1圖の如く熔融小粒子が火花として多數飛散する現象を高速度寫眞によつて撮影研究し,スパッターリングの發生する原因機構を明かにしてゐる.外観的には同じく第1圖の火花として見受けられるスパッターリングもその發生原因は種々あるのであつて,大體目次III~VIIIに示す如くである.VIIIの特殊の場合は第II報に述べることゝして本文は一般の場合に就いて此の各の原因別に高速度寫眞を掲げて之を読明論議する.
著者
伊藤 和博 中川 渉 大西 隆 白井 泰治 村上 正紀
出版者
一般社団法人 溶接学会
雑誌
溶接学会全国大会講演概要
巻号頁・発行日
vol.2013, pp.44-45, 2013

液晶デバイスにおいて、Cu配線とガラス基板との乏しい密着性改善のため、Cu合金膜を用いた手法が試行されている。合金化によりITO膜との接触抵抗増加が懸念され、Cu(M)/ITO界面接触抵抗を低減する検討について報告する。
著者
柳原 大輔
出版者
一般社団法人 溶接学会
雑誌
溶接学会誌 (ISSN:00214787)
巻号頁・発行日
vol.80, no.6, pp.514-517, 2011 (Released:2013-02-21)
参考文献数
6
著者
田中 学
出版者
一般社団法人 溶接学会
雑誌
溶接学会誌 (ISSN:00214787)
巻号頁・発行日
vol.73, no.2, pp.113-118, 2004-03-05 (Released:2011-08-05)
参考文献数
34
被引用文献数
12 13
著者
野村 和史 山下 隼 井村 文哉 浅井 知
出版者
一般社団法人 溶接学会
雑誌
溶接学会論文集 (ISSN:02884771)
巻号頁・発行日
vol.36, no.4, pp.264-273, 2018 (Released:2018-11-15)
参考文献数
28
被引用文献数
2

This study proposed the estimation method of the depth of wed penetration using the experimental measurement of the weld pool shape and the temperature on the front surface during the welding. This method is based on the simple heat conduction calculation, and does not require a flow-field calculation and a heat input information as seen in various welding simulations. In this paper, we first examined the applicability of this method to a bead on plate welding. As a result of application to TIG and A-TIG welding with SUS304 base metal, we obtained the estimated depth with an error of +14∼30% to the actual depth. We investigated this experimental result by the analytical heat conduction model, and found that utilizing the surface temperature with wider area has a possibility to estimate the depth with higher precision.
著者
ヌル サイフラ ビン カマルディン 鈴木 実平 川上 博士
出版者
一般社団法人 溶接学会
雑誌
溶接学会全国大会講演概要 平成19年度秋季全国大会
巻号頁・発行日
pp.168, 2007 (Released:2007-10-23)

アクリル板のレーザ切断溝の形状におよぼす切断速度、レンズ焦点距離の影響を検討した。次に限界切断速度におよぼす焦点距離および板厚の影響を定量的に明らかにした。カーフの入口側の幅はほぼレンズの焦点距離によって決まり、切断速度の影響は少ない。全体のカーフ形状は切断速度によって変化する。
著者
権田 英修 白井 康宏 大橋 修 安井 利明 福本 昌宏
出版者
一般社団法人 溶接学会
雑誌
溶接学会論文集 (ISSN:02884771)
巻号頁・発行日
vol.29, no.4, pp.358-363, 2011 (Released:2012-01-18)
参考文献数
12
被引用文献数
1 1

Generally, cemented carbides (WC-Co) that consist of tungsten carbides and cobalt are used for cutting tools. But since cemented carbides are made of import dependent rare metal, reuse and recycling are required. If cylindrical shanks that the cutting edges are cut off can be combined, it is possible to reuse those shanks as new cutting tools. But in this case, the joining strength of brazing method tends to be rather weak for being used as cutting tools. Instead of the brazing method, the diffusion bonding will be expected with the high strength and the small deformation. Many studies on the diffusion bonding were reported, but there were few studies on the diffusion bonding of cemented carbides.In this study, a potential for applying the diffusion bonding of carbides was investigated. So the effect of the bonding condition on the bending strength, the microstructure of the bonding line and the distribution of tungsten and cobalt were examined. As a result, the strength of the diffusion bonding was higher than that of the brazing at higher than 1100°C, and at 1200°C, it was almost the same as the base metal's strength. Cemented carbides were successfully joined by the diffusion bonding.
著者
金 基成 小溝 裕一 寺崎 秀紀 濱田 昌彦
出版者
一般社団法人 溶接学会
雑誌
溶接学会全国大会講演概要
巻号頁・発行日
vol.2008, pp.234, 2008

Ni量を変化させた低炭素鋼溶接金属をTIG溶接したときの凝固過程を放射光を用いた時分割X線回折でその場観察した結果を発表する。同定したδ相とγ相、液相を示すハローパターンからNi量の変化によって凝固モードが遷移することを直接観察した。
著者
植田 治久
出版者
一般社団法人 溶接学会
雑誌
溶接学会誌 (ISSN:00214787)
巻号頁・発行日
vol.78, no.1, pp.42-46, 2009 (Released:2014-02-12)
参考文献数
7
著者
植松 美彦 戸梶 惠郎 戸崎 康成 柴田 英明
出版者
一般社団法人 溶接学会
雑誌
溶接学会論文集 (ISSN:02884771)
巻号頁・発行日
vol.27, no.4, pp.261-269, 2009 (Released:2009-10-23)
参考文献数
16
被引用文献数
4 7

Fatigue tests were conducted under fully reversed axial loading (R = -1) in laboratory air and 3% NaCl solution using friction stir welded (FSW) joints of 7075-T6 aluminium alloy sheets. The FSW joint exhibited lower tensile strength than the parent metal. Heat input during FSW process re-dissolved strengthening precipitates, resulting in softening in the weld zone and lower tensile strength. In laboratory air, the fatigue strength of the FSW joint was comparable to that of the parent metal, which could be attributed to grain refinement in the stir zone (SZ) and dynamic aging during fatigue loading in the softened weld zone. In 3% NaCl solution, the fatigue strength of the FSW joint was lower than that of the parent metal. Corrosion pits were preferentially formed at the boundary between thermo-mechanically affected zone (TMAZ) and heat affected zone (HAZ), which led to premature crack initiation in the FSW joint. Such predominant formation of corrosion pits was due to the sensitization caused by heat history during FSW process.
著者
川上 博士 西河 厚志 吉村 幸治 駒田 将樹 鈴木 実平
出版者
一般社団法人 溶接学会
雑誌
溶接学会論文集 (ISSN:02884771)
巻号頁・発行日
vol.35, no.1, pp.21-28, 2017
被引用文献数
1

The properties of rotating tool spot joining joints with different rotating tools by the combination between the shoulder diameter and the probe length were investigated in this study. The shoulder diameter of rotating tool affects the tensile strength of the joint significantly. An oversize shoulder diameter decreased the joint strength. The probe length affects more the fracture mode than the joint strength. Interface fracture mode occurred with a rotating tool of short probe length. Plug fracture occurred with a rotating tool of long probe length. Rotary motion of restricted area in the joining interface by the rotating tool was confirmed by displacements of the joining interfaces. Rankin vortex was observed on the joining interface by velocity distribution of rotary motion of joining interface. Al oxide film layers were formed spirally on upper joining interfaces
著者
栗原 正好
出版者
一般社団法人 溶接学会
雑誌
溶接学会誌 (ISSN:00214787)
巻号頁・発行日
vol.66, no.1, pp.6, 1997-01-05 (Released:2011-08-05)
参考文献数
3
被引用文献数
3 3