著者
菊地 伸二 Shinji Kikuchi
雑誌
研究紀要 = Nagoya Ryujo Junior College annual report of studies (ISSN:13427997)
巻号頁・発行日
vol.36, pp.53-61, 2014-12-20

アウグスティヌスは、カトリック教会に回心した後、約15年間にわたり、さまざまな「マニ教反駁書」の執筆にとりかかる。この小論では、「マニ教反駁書」の中でも、とくに、聖職の道を歩み始めた後に書かれた二つの作品である『二つの魂』と『マニ教徒フォルトゥナトゥス駁論』を取り上げて考察する。この二つの作品において、アウグスティヌスは、マニ教が主張するところの善悪の二つの本性を徹底的に批判するとともに、悪の原因を人間の自由意思のうちに求めていくが、そのような人間の自由の擁護は、神の自由というより完全な姿を前提とすることによって成立するものである。また彼は、「マニ教反駁書」を執筆するという営みの中で、マニ教徒の「パウロ書簡」の解釈に出会うとともに、そのような解釈を批判する中で、自らが「パウロ書簡」のより精緻な読解へと導かれていくのであり、そのことが彼の「自由意思」の理解を深めることにつながっていくのである。
著者
岡田 義浩 農沢 隆秀 坪倉 誠 中島 卓司
出版者
一般社団法人 日本機械学会
雑誌
日本機械学会論文集 (ISSN:21879761)
巻号頁・発行日
vol.80, no.809, pp.FE0009, 2014 (Released:2014-01-25)
参考文献数
14
被引用文献数
1 2

In order to clarify unsteady flow structure’s behavior that improves vehicle’s high-speed stability during steering input, on-road analysis was conducted. The analysis was conducted on two vehicles’ aerodynamic specifications which were produced by configuring two different shapes from a single vehicle. During high speed driving while steering input in sinusoidal waveform was being applied, these two vehicles were analyzed focusing on the relationships between dynamic movements, unsteady forces affecting on vehicle’s body surface and unsteady behavior of flow structure. As a result, it was clarified that there existed a unsteady behavior of flow structure that aerodynamically control to stabilize vehicle’s steering response motion in vertical and yawing direction. It was also clarified that this aerodynamic force that control to stabilize vehicle’s steering response motion was caused by behaviors of flow structure beside body just behind front tire which reduced and expand its vertical scale during high-speed driving with steering input. Furthermore, it was shown that this behavior of flow structure was caused by weakening vortex structure which came out and separated from the gap between the upper rear side of the front wheel and the front wheel arch.
著者
稲田 幹
出版者
公益社団法人 日本化学会
雑誌
化学と教育 (ISSN:03862151)
巻号頁・発行日
vol.69, no.1, pp.20-23, 2021-01-20 (Released:2022-01-01)
参考文献数
4

プラスチック(有機材料),金属,セラミックスは三大材料である。プラスチックや金属は高温で溶かして成型加工できるが,セラミックスは基本的に粉を固めて焼く『焼結』という方法で製造される。そのため,セラミックスの製造には,原子・分子レベルからの原料粒子調製技術,粒子集合体への成形技術,焼結の制御が高度に要求される。一方で,高温耐熱性,高強度,半導性,誘電性,磁性などのセラミックスの多様な特長は,構成原子の化学的な結合や構造と密接に関連している。