4 0 0 0 OA 核生成

著者
木村 勇気 川野 潤 田中 今日子
出版者
北海道大学
雑誌
基盤研究(S)
巻号頁・発行日
2015-05-29

核生成は物質形成の始まりであり、物理的、化学的なメカニズムの解明は多分野にまたがる非常に重要な課題である。本研究では、1)気相からの核生成実験、2)計算機シミュレーション、3)核生成の透過電子顕微鏡(TEM)中その場観察実験の3つのアプローチを行うことで、核生成と前駆体のかかわりを直接的に示すことを目的としている。本年度は、それぞれに関して、以下に記す実績が得られた。1)気相からナノ粒子が生成する場合であっても、初めに生成したクラスターが成長ユニットとなり、方位をそろえて接合しながら成長することで、最終生成物が形成することが分かった。結晶成長分野で最近注目されている多段階核生成の解明に迫る成果であり、論文としてまとめてNanoscaleに報告した。2)昨年成功した、最大1500万の希ガス分子(Lennard-Jones分子)を用いた長い待ち時間の計算による、気相から過冷却液滴への核生成と液滴からの結晶化という多段階核生成過程の再現をまとめ、Physical Review Eに報告した。3)コンクリートの劣化を防ぐ為に使われるシリカ粒子と水酸化カルシウム溶液を用いて単純化したコンクリート化の初期過程のTEM中その場観察実験を行った。その結果、まずシリカ粒子の膨潤によってコンクリート内の細孔が埋められていき、その後、カルシウムケイ酸塩水和物が形成して粒子同士をつないでいくことで固化が進むプロセスを捉えた。わずか0.03 nm/秒というシリカ粒子が膨潤する典型的な速度の実測にも成功した。溶液セルを用いたTEMその場観察実験により、他の手法では殆ど不可能である個々のナノ粒子の水和による膨潤や溶解、成長の微小な速度を求めることが可能になった。本成果を論文としてまとめ、Industrial & Engineering Chemistry Researchに報告した。
著者
田中 茂喜 佐々木 崇文 石黒 奈央 浦野 孝太郎 小山 秀一 木村 勇介 町田 登
出版者
公益社団法人 日本獣医師会
雑誌
日本獣医師会雑誌 (ISSN:04466454)
巻号頁・発行日
vol.72, no.3, pp.162-166, 2019-03-20 (Released:2019-04-20)
参考文献数
14
被引用文献数
1

爪床悪性黒色腫の心臓転移がみられた犬の完全房室ブロック(CAVB)症例について,ブロック発生の形態学的基盤を明らかにすべく,心臓刺激伝導系を中心に詳細な病理学的検索を施した.本例は,死亡する11カ月前に右前肢の第5指に発生した悪性黒色腫の外科的切除術を受けていた.剖検時,心臓の割面では暗褐色〜黒褐色の腫瘍組織が,心筋層内に多発性の増殖病巣を形成していた.病巣部の組織学的検索により,悪性黒色腫の心臓転移と診断された.腫瘍性のメラノサイトは房室接合部領域にも重度に浸潤しており,房室結節は完全に消失していた.この病的機転はヒス束貫通部をも巻き込んでおり,当該部位の伝導系細胞は全長にわたって消失していた.このような房室伝導系病変が,インパルスの房室伝導を遮断したものとみなされた.
著者
中谷 朋昭 木村 勇輝 橋本 大佑
出版者
日本フードシステム学会
雑誌
フードシステム研究 (ISSN:13410296)
巻号頁・発行日
vol.24, no.2, pp.82-93, 2017 (Released:2017-12-23)
参考文献数
22
被引用文献数
1 1

The Japanese diet is known for its ideal balance of the three macronutrients, namely protein, fat, and carbohydrates. Dietary statistics indicate that over time, in Japan, these macronutrient ratios have been maintained since the mid-1970s in close agreement with favorable macronutrient ratio intake standards, set by the Japanese Ministry of Health, Labour and Welfare. The ideal ratio is principally achieved by reducing carbohydrates, while increasing fats. However, in recent years, this macronutrient ratio appears to depart from ideal ranges, due to over-westernization of the Japanese diet. To investigate the extent of this phenomenon, we analyzed a time series data set for ingested nutrition by using cointegration techniques to identify long-run, stable relationships among the three macronutrients, between 1956 and 2015. Next, we set a restriction on the cointegrating vectors, representing ideal macronutrient ratio standards. This restriction was used as the null hypothesis that the detected long-run relationships among the three macronutrients were favorable, compared to the idealized macronutrient intake standard. We run the likelihood ratio tests for the full sample and sub-samples, by recursively increasing the number of observations obtained since 1978. Our results reject the null hypothesis, at the conventional level of significance, for the full sample and almost all sub-samples. These outcomes indicate that although the Japanese diet between the late 1980s and early 2000s were the closest to the ideal macronutrient ratios of proteins, fats, and carbohydrates, it is diverging since that time from these favorable ratios.
著者
佐々木 崇文 中尾 周 木村 勇介 平川 篤 町田 登
出版者
公益社団法人 日本獣医師会
雑誌
日本獣医師会雑誌 (ISSN:04466454)
巻号頁・発行日
vol.73, no.6, pp.315-320, 2020-06-20 (Released:2020-07-20)
参考文献数
15
被引用文献数
1

第3度房室ブロックを示した猫22例の心臓について,詳細な病理学的検索を実施した.これら22例の基礎心疾患は,肥大型心筋症10例,拘束型心筋症(心内膜心筋型)3例,不整脈源性右室心筋症2例,陳旧性心筋梗塞1例であり,残り6例の心臓に明らかな病的変化は認められなかった.房室接合部の組織学的検索では,基礎心疾患の有無やその種類に関係なく,全例の中心線維体基部と心室中隔頂上部に重度の線維増生(心臓骨格左側硬化)が認められた.こうした病的変化は同領域を走行する房室伝導系を巻き込み,伝導系細胞の脱落を引き起こしていた.なお,房室伝導系の重度傷害はヒス束分岐部から左脚上部に主座しており,高齢者にみられる特発性ブロックの原因であるLev病に類似していた.
著者
木村 勇気 勝野 弘康 平川 靜 山﨑 智也
出版者
公益社団法人 日本表面真空学会
雑誌
表面と真空 (ISSN:24335835)
巻号頁・発行日
vol.66, no.12, pp.700-705, 2023-12-10 (Released:2023-12-10)
参考文献数
27

Non-equilibrium processes such as nucleation are difficult to observe in situ using transmission electron microscopy (TEM) because of spatiotemporal stochastic process. Therefore, we have been developing a method to predict/detect nucleation events and observe under low electron doses conditions in real time with the support of machine learning. Low electron dose observation is important to avoid radiolysis of water in the observation of aqueous solutions using liquid-cell TEM. Our data-driven TEM that can suggest observation points to the operator by processing in situ observation data in real time. In other words, it is data-driven TEM in which the TEM helps the operator, rather than the TEM being driven by the data. By incorporating the two codes into the TEM's software, nucleation can now be observed efficiently.
著者
木村 勇気
出版者
公益社団法人 応用物理学会
雑誌
応用物理 (ISSN:03698009)
巻号頁・発行日
vol.92, no.9, pp.545-549, 2023-09-01 (Released:2023-09-01)
参考文献数
31

宇宙にはダストと呼ばれる無数のナノ粒子が存在しており,さまざまな場面で重要な役割を果たしているため,ダストの形成過程の理解は天文学,惑星科学の土台となる課題である.我々は気相からの核生成過程の一般性と,宇宙における物質進化を理解する鍵はナノ領域特有の性質にあると考え実験を基に研究を行ってきた.その結果,気相からの均質核生成のキーファクターはダイマーの形成と融点降下にあることが分かり,ダストの形成過程の理解にはナノ粒子の融合成長を考慮する必要があることが分かってきた.ここでは,最近の研究の一端を紹介する.
著者
甲斐 拓海 清原 克哲 中森 友啓 木村 勇太 木村 加奈子 嘉戸 直樹 鈴木 俊明
出版者
関西理学療法学会
雑誌
関西理学療法 (ISSN:13469606)
巻号頁・発行日
vol.22, pp.95-100, 2022 (Released:2022-12-23)
参考文献数
6

We report the case of a man in his 50s with decreased endurance in gait after brain tumor resection. His main complaints were that he felt pain on the right side of his waist and that he could not walk for long periods. We observed that during the left loading-response phase, he could not adduct his left hip joint, nor could he move his pelvis to the left. Therefore, during the initial swing phase, he put his right plantar foot down quickly and his trunk tilted forward. This resulted in flexion of the thoracolumbar transition during the right loading-response phase and extension of the thoracolumbar transition during the right mid-stance phase. The patient repeated this gait pattern, and after about 3,000 steps, he developed pain in the right lumbar region. We considered the main problem to be weakness of the left hip adductor muscle, and treated the patient with physical therapy. As a result, left hip adduction became possible during the left loading-response phase, and the pain in the patient’s right lumbar region improved, resulting in improved endurance of walking. In this case, physical therapy with a focus on the left adductor magnus muscle was effective at improving the pain in the patient’s right lumbar back and the functioning of the hip adductor muscles required during the left loading-response phase.
著者
白尾 恒吉 木村 勇 仲根 孝 井上 政久 岩堀 信子 本間 龍雄
出版者
青山学院大学
雑誌
一般研究(C)
巻号頁・発行日
1986

数学の各分野において近年国際的発展のはなはだしい研究を見る組合せ論的な扱いを主として、我が数学教室においては、代表者白尾は、マルコフ過程の從来の解析的思考を組合せ論的な立場から見直すべく出来るだけ夛くの知識と概念を導入して来年度への研究の活力とした。分担者岩堀は、組合せ論properな未解決問題をプログラムし、計算実験をくりかえし、いくつかの部分的な成果および予想を得た。分担者本間,井上は或る種の非代数的曲面の変形の研究から新しい非代数的低次元複素夛様体を構成することを試みた。分担者小池は、昨年夏の日米合同セミナー"可換群と組合せ論"(バークレイ)において、Littlewood's公式に基き、(対称な有理関数のShier関数への展開公式)偶数次の対称群とワイル群の間の既約表現に関連する分解公式を得た。以上、いくつかの方面からの研究をひろく行ったが、いづれもコンピューターによる補助計算、実験計算等に夛くの時間をかけているので、結果を得られたものもあるが、未だその途上に研究をつづけているものが夛数あるのでこれらを来年度の課題としたい。
著者
木村 勇喜 百田 武司
出版者
日本赤十字看護学会
雑誌
日本赤十字看護学会誌 (ISSN:13461346)
巻号頁・発行日
vol.21, no.1, pp.88-93, 2021-03-31 (Released:2021-03-31)
参考文献数
15

目的:緊急入院した高齢者で,せん妄回復時に消失したせん妄発症要因を明らかにする.方法:緊急入院した65歳以上の患者で,せん妄評価尺度(ナース版)において,せん妄を発症した35人を対象に,診療録から調査を行った.結果:せん妄回復時に消失したせん妄発症要因は,「疼痛」,「発熱」,「血清クロールの異常」,「ベンゾジアゼピン系薬剤の使用」,「侵襲の多い検査・処置」,「経皮的酸素飽和度の異常」,「治療拒否の訴え」,「不安の訴え」,「不眠の訴え」,「時計の不設置」がせん妄発症時に比べ,せん妄回復時で有意に少なかった.結論:緊急入院した高齢者のせん妄回復時に消失したせん妄発症要因が明らかになり,せん妄発症後,せん妄回復に向けた看護援助の方向性の示唆となった.
著者
木村 勇太 伊藤 毅志
出版者
一般社団法人 人工知能学会
雑誌
人工知能学会全国大会論文集 第32回 (2018)
巻号頁・発行日
pp.1H1OS13a03, 2018 (Released:2018-07-30)

従来の人狼AIでは、役職の推定は製作者によりヒューリスティックに決められてきた.本研究では既存エージェントの推定部分に機械学習の一つであるSVR(Support Vector Regression)を導入しその有効性を検証した.その結果,中盤以降で従来の手法を上回る推定率を実現することが出来た.また,序盤では従来の手法,中盤以降では提案手法を用いるエージェントを構築することで,従来のエージェントを有意に上回る勝率を実現することが出来た.

1 0 0 0 秋川創設記

著者
木村勇三編
出版者
メタセコイア友の会
巻号頁・発行日
1973
著者
木村 勇次 井上 忠信 中田 隆之 福田 又一
出版者
一般社団法人 日本機械学会
雑誌
日本機械学会論文集 (ISSN:21879761)
巻号頁・発行日
vol.84, no.860, pp.17-00493, 2018 (Released:2018-04-25)
参考文献数
24
被引用文献数
1 7

Delayed fracture susceptibility of 1.8 GPa-class ultra-high strength bolts was evaluated by an outdoor exposure test. Low-alloy steel bars with a chemical composition of Fe-0.4%C-2%Si-1%Cr-1%Mo (mass%) were quenched and tempered at 500 °C for 1 h, caliber-rolled at 500 °C with a rolling reduction of 78%, in order to create fail-safe steels (FS steels) with an ultrafine elongated grain structure. Subsequently, FS steel bars were formed into JIS M12 hexagon head bolts with a nominal length of 60 mm (FS bolts). Bolt heading was performed at 700~730 °C, and screw part was formed by thread-rolling at 500 °C to maintain the ultrafine grain structure with a strong <110>//rolling direction fiber texture. Conventionally quenched and tempered bolts (QT bolts) with a tempered martensitic structure were prepared for comparison. A steel plate was fastened by the bolts on 23 April 2013, and the outdoor exposure test was started on 21 May 2013 in Miyako Island test site of Japan Weathering Test Center. The bolt fastening force was 122 kN (=0.85 σ0.2 at thread part) for FS bolts and 89 kN (=0.70 σ0.2 at thread part) for QT bolts. The outdoor exposure test demonstrated an excellent delayed fracture resistance of FS bolts at the ultra-high tensile strength of 1.8 GPa; FS bolts have not been broken for 53 months, in contrast to QT bolts exhibiting delayed fracture. Intergranular cracking along the prior-austenite grain boundaries was commonly observed in the broken QT bolts. The accelerated laboratory test using tensile tests of pre-hydrogen-charged specimens and immersion test (30 °C, pH2) showed that the FS bolts had high resistance to hydrogen embrittlement, and it was in good agreement with the result of outdoor exposure test of the FS bolts.
著者
木村 勇一 大久保 隆夫 後藤 厚宏
出版者
FIT(電子情報通信学会・情報処理学会)運営委員会
雑誌
情報科学技術フォーラム講演論文集
巻号頁・発行日
vol.13, no.1, pp.119-120, 2014-08-19

既存Webアプリケーション(WebAP)の入力処理の脆弱性を調査し,対策を考察した.2014年4月に広く認知されたStruts2,及びStruts1の脆弱性(Struts脆弱性)は,Javaの基本的な枠組みで発生する脆弱性である.課題はWebAPの内部構造のブラックボックス化とパラメタの正否を識別する仕組みの欠如である.対策としてホワイトリストのパラメタチェックフィルタがある.ホワイトリストは必要なパラメタのみ取り込み,その他のパラメタを除外するので,ブラックボックスとなるコンポーネント利用時の未知の脆弱性の防止に有効である.対策となるチェックルールの設定方法3案を提示する.
著者
飛鷹 秀幸 木村 勇次 高木 節雄
出版者
社団法人日本鉄鋼協会
雑誌
鐵と鋼 : 日本鐡鋼協會々誌 (ISSN:00211575)
巻号頁・発行日
vol.85, no.1, pp.52-58, 1999-01-01
被引用文献数
6

Mechanical milling using high energy planetary ball mill was applied to Fe-C alloy powders with (ferrite+cementite) two-phase structures to give an ultimate large strain into the powders. Dissolution behavior of cementite during mechanical milling was investigated in relation to ultra grain refining of ferrite matrix, and dissolution capacity of cementite was discussed in terms of carbon content in the powders. Ultra grain refining of ferrite matrix to about 10nm results in full dissolution of cementite in the powders with carbon up to 2 mass% C. Most of carbon, which has been rejected from decomposed cementite, is suggested to segregate at grain boundary to form amorphous layer. Thus, it was proposed that the dissolution limit of cementite depends on both volume fraction of the grain boundary amorphous layer and carbon concentration therein. For example, as the maximum carbon content of the grain boundary amorphous layer was to be about 4.2 mass% C, the dissolution limit of cementite was estimated at 30 vol% from the mass valance for carbon content in the case ferrite grains were refined to around 10nm. This volume fraction of cementite is just correspondent to that in Fe-2mass%C alloy.
著者
木村 勇雄 金谷 貢
出版者
一般社団法人日本歯科理工学会
雑誌
歯科材料・器械 (ISSN:02865858)
巻号頁・発行日
vol.28, no.5, 2009-09-10

The final purpose of this study is to develop a high-performance implant, which can prevent infection for a couple of day immediately after the operation and then promote the osseointegration. As a fundamental study, hollow calcium-deficient hydroxyapatite microspheres revealing high solubility were made to adhere onto a titanium screw, of which the surface had been treated with hydrofluoric acid. The effects of conditions for the surface treatment on the surface morphology of titanium and the adhering amount of the microspheres were investigated.
著者
津崎 兼彰 山口 隆司 増田 浩志 木村 勇次
出版者
独立行政法人物質・材料研究機構
雑誌
基盤研究(A)
巻号頁・発行日
2008

本研究では、超高力ボルト創製に関する基礎研究を材料・建築・土木分野の研究者が共同で行った。その結果、1800MPa級超高力ボルトを実現するための最適材料化学成分と金属組織ならびにボルト形状を提案した。