著者
太田 裕之 藤井 聡
出版者
公益社団法人 土木学会
雑誌
土木学会論文集G (ISSN:18806082)
巻号頁・発行日
vol.63, no.2, pp.159-167, 2007 (Released:2007-06-20)
参考文献数
20
被引用文献数
1 2

現代社会において,CO2排出削減のための環境配慮行動は多様に存在し,そのような中で人々は優先的にいくつかの行動を選択し取り組んでいると考えられる.その行動の選択の際に影響する要因の一つとして考えられる「有効性知覚」は,様々な認知的バイアスの影響により,実際の有効性と必ずしも一致していない可能性があると考えられる.そこで本研究では,CO2排出削減量効果の情報を提供することで,人々の有効性知覚と客観的有効性との間の乖離が減少し,それに伴い行動の効率化がなされるとの仮説を措定し,アンケート調査形式の実験を行った.データ分析を行った結果,事実情報の提供により認知的ひずみは軽減し得るものの,行動意図は十分には効率化されない可能性があるとの結果が示唆された.

1 0 0 0 OA 路傍の花

著者
徳田秋声 著
出版者
新潮社
巻号頁・発行日
1919
著者
小久保 祐樹
出版者
首都大学東京小笠原研究委員会
雑誌
小笠原研究年報 (ISSN:03879844)
巻号頁・発行日
no.37, pp.1-30, 2014-05-31

小笠原における所有者不明土地問題について、行政が行うべき法政策的対応について政策提言を行った。はじめに、小笠原における所有者不明土地問題についての現状の調査を行った。次に、所有者不明土地に対する法政策的手法の事例紹介を行い、小笠原における所有者不明土地問題に対する法政策的対応策の提案を行った。この提案では、条例の制定が適切であると結論付けた。最後に、条例制定の際に問題となる財産権規制に対する学説分析を行い、具体的な条例の内容に関して考察した。
著者
吉村 博仁 堀田 恭平 星 幸義 永澤 克浩
出版者
一般社団法人 日本機械学会
雑誌
日本機械学会論文集 (ISSN:21879761)
巻号頁・発行日
vol.83, no.853, pp.17-00094-17-00094, 2017 (Released:2017-09-25)
参考文献数
15
被引用文献数
1

In recent years, needs for micro drilling are increasing, accompanying the development of higher wiring density of printed circuit board (PCB). When drilling PCB for the purpose of making the electric through holes, it has been said that the drill breakage is caused by being filled the chips of GFRP and copper of PCB in the drill flutes. The aim of this study is to clarify the effect of PCB drilling using DLC coated drill on tool wear, chip evacuation and cutting torque. Series of drilling tests of PCB have been carried out to investigate the amount of drill wear, the chips evacuation behavior out of drilled hole with the drill, the shape of chips produced and the cutting torque using DLC-coated drill and non-coated drill. The chips evacuation behavior out of drilled hole with the drill is filmed by a high-speed motion camera and the shape of chips produced is observed by a microscope. The cutting torque is measured by a dynamometer; Kistler 9329A. The amounts of drill flank wear and margin wear using DLC-coated drill and non-coated drill are almost the same. The chips of GFRP using DLC-coated drill are shorter and smaller than those using non-coated drill. The chips evacuation out of drilled hole with the drill using DLC-coated drill is better than those using non-coated drill, and cutting torque using DLC-coated drill is lower than those using non-coated drill.

1 0 0 0 OA 史記評林130卷

著者
明凌稚隆輯
巻号頁・発行日
vol.[2], 1000
著者
薄井坦子著
出版者
現代社
巻号頁・発行日
1994

1 0 0 0 OA 史記 130卷

著者
(漢) 司馬遷 撰
出版者
[出版者不明]
巻号頁・発行日
vol.第11册, 1606
著者
鈴木経勲 述
出版者
博文社
巻号頁・発行日
1894